snapmaker 2 a350 3d models

This part is a remix of a A350 part to make it if in a A250 where a) The rear part is split in two with a lock mechanism and can be printed in A250 b) Holes are displaced as the original part obstructs the case cable hole in an A250

I made this Bowden Tube fitting adapter for the Snapmaker 2.0 because I came across a design https://www.thingiverse.com/thing:4628630 and printed and the mounting holes were quite far off and trying to make it work would of required either...

These are fan holders for the Powersupply of the Snapmaker 2.0. The little fans are making a lot of noise so i removed them and put a fan in the front and a fan in the back to create an airflow through the powersupply. I inserted 2 80mm fans from...

This is a filament holder for the Snapmaker 2. Originaly designed to fit the 350 version , but you only need to shorten the tube between the mounts to fit it to the 150 or 250 enclosure. This files is sold as a digital file, so you need to print...

The Snapmaker 2.0 3D print toolhead comes with a poor performance part cooling. This is upgraded version of 5015 kit by brent113, but with stronger mount (use bolts and nuts from stock cooling system), better printability (splitted duct and mount for...

This is a set of parts that are meant to accessorize the Snapmaker 2.0 for easier use to store Tool heads. This is my V2 design which includes a notch on the side to accommodate the filament loading door release on the front of the 3D Printhead. In...

I was having problem with my snapmaker calibration so I found this useful instructables that showed how to calibrate with a laser pointer. https://www.instructables.com/Calibrate-3D-Printer-or-Other-CNC-Machine-With-Las/ Naturally I wanted...

Works with the Logitech K260 keyboard. ...Print Settings Printer: Snapmaker 2.0 A350 Rafts: No Supports: No Resolution: 200 Infill: 15 Filament: eSUN PLA+ Black Category: Gadgets

... the shelf at the bottom so that no supports are required for printing. ... It uses a 50 degree angle, but printed very well on my Snapmaker using Overture's Black PLA.I used some 10mm x 5mm magnetics from Amazon: https://www.amazon.com/dp/B0CJ6NYNZ6

These are designed to use the same M4x10 flat head screws that are used to secure the 3d Print Bed and attach nicely to the side of the Snapmaker for a clean look and easy storage out of the way of any moving parts. ... (Power supply holder is not my...

Hierzu folgende Zeilen in der config.g ergänzen (der Lüfter hängt im Beispiel an "out6"): M308 S10 Y"mcu-temp" A"MCU"M308 S11 Y"drivers" A"TMC" M950 F4 C"out6" Q50 ; die Sunon-Radiallüfter brauchen 50Hz PWM, sonst stottern sie M106 P4 H10:11 T40:70...

Replace the Induction proximity sensor in the Snapmaker 2 print head with an Infrared one to enable auto leveling on a glass bed. Full instructions, parts list and links to suppliers are in the included document. ###Disclaimer For this project...

the lower right hand side means the tool head doesn't have to be lifted very far before it can be removed and the longer left side means it is secure and gives a large edge to locate the tool head before sliding it in place.this is the 3rd attempt to...

With the recent release of the Snapmaker Quick Swap plates, I needed a way to store my unused beds in storage. With the Quick Swap Plate attached to the bottom of the bed, they do not sit flat in my drawer, so this part acts like a tray for the bed...

The cable cover fits below the splitters of the A250 and A350. It prevents squashing and tangling cables, e.g., when relocating the device. Unlike the previous variants, this one is perforated and works with M4x8 screws (see images). Cable clips...

AboutI wanted to be able to conveniently place my Snapmaker's display on top of the enclosure and turned to the side, however wanted to keep it easy to move back to the enclosure and up again. ...So I've created this magnetic mount design that can slide...

But I had changed where the Snapmaker Spool mounting bar hardware was located on the enclosure. I put it on the back of the enclosure flat against the back acrylic panel. See pictures. While the original design worked fine, it was hard to...

Install a Dial Indicator on a Mount with Lug. ... Utilized threaded inserts include: 2 x Ruthex M4 1 x Ruthex M5

This Version has an additional 8mm hole for a 5.5mm x 2.xmm coaxial power connector for utilizing the 24V for custom add-ons. ... Update: Revised the Plates to correct incorrect dimensions caused by a faulty caliper measurement.

... the instructions. ... I used (#12) 1/2 inch screws. Needed a window vent adapter for the window vent I got from amazon but still wanted to close the space at night or when the 3D printer was not in use. ... https://www.amazon.com/dp/B087WKKQHB/

This design offers a quick change adapter that will take 15-20 seconds to change a tool heads Photos are for 2 tool head shifts. took less than 38 seconds. For fixings, you shall require: - 12 countersunk 4X10mm screws - 4 screws 4X20 mm and 8 nuts...

This attaches to the holes in the 24x24 side beam (2 x M4x15 screws) and puts the spool at a 30° angle. The bearing is something I found and fits directly onto the old spool holder. Bearing dimensions are inner ⌀ 8mm, outer ⌀ 16/18,5mm, thickness 5mm...

... only sell 400x400 but will cut if for you at request. At the time of my purchase the total cost including delivery was £68.92 i modified the walls to be 27mm tall, instead of the previous 24mm. Approximately 9hrs to print 2 at 100% infill. ...

Hi,This is an reduction/adapter for the Snapmaker2 screw driver (maybe it goes for all of them) that it has Allen key 3 within the handle: )The part here attached I have not printed, but an earlier one with hand customization like in the photo, than...

The provided images showcase version 1, featuring longer corners, shorter rails, and larger clamps; however, the downloadable files are from version 2, which boasts smaller corners, extended rails, and reduced clamps. I appreciate your interest in...

Remixed from https://www.thingiverse.com/thing:5932726I've simplified everything possible on this fan bracket and gained some benefits.print in placeclip on and off with one hand.designed as thin as possible and still stable2 beveled screw holes on...

The pictures are from v.1 (longer corner, shorter rails and bigger clamps), but the files are from v.2 (smaller corner, longer rails and smaller clamps). Hope you appreciate it! All the best! UPDATE - 2018-09-26 Thanks to Kogomonier's...

Bearing: 608RS*2 Pros: ·Compatible with spools with an inner diameter of 50mm to 55mm. (I measured several filament spools from different brands I own) · Compatible with spool up to 160mm deep. · Quick swap without take parts off · Very...

Name: Tiny Snapmaker Designer: Howard Info: This compact Snapmaker 3D printer packs a big punch. ... More Details are available in the snapmaker community forum at http://forum.snapmaker.com.

The model is within a couple of percent of the actual dimensions of the aircraft. It is fully textured and moderately detailed model. It is textured with multiple large HD maps and provides a good realistic rendering when lighted and animated...