snapmaker 2 a350 3d models

A shorter version of the Vacuum Attachment to work with the original snapmaker 2 enlosure. ... The original version is too long so with an attached hose it will fall off during homing.

Very simple Snapmaker 2 power supply stand. It is versitile and can be mounted on the side of an enclosure and on a flat surface. ...I printed 3 and have two on the bottom and one on top.

For testing if it can slide into your Snapmaker 2.0 enclosure frame. ... It might be difficult to slide in for the 1st time, just don't give up too early.

This is a corner brace designed for use with the snapmaker 2.0 CNC wasteboard. ...The hole spacing is 50 mm, and the hole diameter works with the M4 bolts included with your machine.

STL Model of the CNC Spoil Board for the SnapMaker 2.0. Helpful for laying out parts for machining and / or generating fixtures and jigs. ... Please let me know if anything is out of place.

Fan adaptor to replace to stock fan of the Snapmaker 2.0 power supply (PSU) by a 40x40x10 fan without replacing the backplane. ... I tapped the part for M3 nuts/screws.

Power Supply mount for Snapmaker 2.0. Needs to be printed twice and can be mounted to just about anything. ...I mounted mine to the back of my enclosure and it fits nicely.

A bumper created to be attached to Snapmaker 2.0 Y Linear Module's end where the hot bed cable can potentially get caught, thus causes printing mat to be shifted.

The Snapmaker 2 enclosing provides no space to store the filament. ...Just snap the holders into the top left horizontal bar of the enclosing and out the filament roles in place.

3D Model of Snapmaker 2.0 3D Printer tool head for making add-ons/mods. ...May not be 100% accurate, but should be close enough to modelling exterior add-ons.

This is an elbow for the enclosure on the Snapmaker 2.0. ...I would imagine most of you have your printers on a desk like mine and attaching a flexible duct for the exhaust fan was a bit tight.

This bushing clips into the Snapmaker 2.0 Enclosure's filament passthrough bushing and holds a short section of 4mm OD PTFE tubing to reduce friction from the filament sharply changing direction.

Stuck my SnapMaker 2.0 power supply with Nano tape to the underside of my table. This bracket is a safety feature should the tape not hold. ...The Nano tape I used is about 2mm thick.

I run a filament drying box inside the Snapmaker 2.0 Enclosure and rote the filament up and over the filament spool holder that comes with the Snapmaker 2.0. In preparation for the dual-filament print head and being able to string two different...

This one is designed to hold the modules of Snapmaker 2.0. Needs about 200 grams of filament and 22 hours of printing time with the settings above. ... There is also a version for Snapmaker Original which you can find here:...

This is a quick release plate for the Rotyry module for the Snapmaker 2.0. The plate works for the 250mm module. For the 350mm module the construction is a bit too unstable. I am still working on a suitable solution. ...Everything you need: 4 x 4x8mm...

I wanted to attach standard 4" exhaust ducting to my Snapmaker A350 enclosure so I could use inline duct ventilation fans to exhaust my laser fumes more effectively. This adapter allows a direct connection, and uses the existing holes and screws...

Helps protect and support the Snapmaker's heated bed cable

Because the cable of the Snapmaker 2 heated bed has no strain relief I've created a small helper. Replaces the original "cable holder" - just remove the 2 M3 screws. Reuse the M3 nuts and screws in my design Extra materials needed: 2 pcs. screw M4 -...

I've had a chance to get a better look at the new platform as someone has taken the time to model it which makes it a lot easier to inspect it without having it physically:...

This is a remix for A250 of the Snapmaker Organizer 2 fromby btkuhn I just cut it in 2 part as it can be printed in a 25*25 3D printer just have to glue it after print the 2 parts

https://forum.snapmaker.com/t/my-new-snapmaker-2-0-a351/16502 All parts are listed below. All brackets attach to the Snapmaker with M4x10 bolts. The chains are attached with 3x M3x8 bolts and nuts. The tool head cable will need to be spliced with...

A : Clear Storage Clips Sewing Craft Quilt Binding Plastic Clips Clamps...

Snapmaker 2.0 endoscope camera holder. The camera mount is designed for commonly available 5.5mm endoscopes and could be easily modified to accommodate different type of endoscope. Requires a pair of M3*12mm screws and nuts. Could use 10mm...

Simple laser test for Snapmaker 2, this is ideal for finding out what speed/power is needed on various materials. I strongly advise not leaving the machine unattended while running this as full power/slowest speeds can burn through certain...

... 543-781B). Compatible with the snapmaker 1.0 and 2.0 mounting plate. Can be used to check for example flatness of the printing bed or laser & CNC materials. ... I recomondate to use my quick tool changer: https://www.thingiverse.com/thing:4700986

A stand to mount the Snapmaker 2.0 power supply sideways inside a custom enclosure or next to your printer and save a little space. ...They are designed with counter-sunk holes for mounting, and slightly wide to allow for a piece of felt to protect the...

Snapmaker Laser Bed Work Holding Clamps Printed with 3D Fuel Pro PLA Nozzle: 0.2 Nozzle Temp: 210 Slicer: Cura Resolution: High Fits snuggly between fins of the laser bed. Has adjustable jaw to clamp work piece. Snap jaw onto end of thumb screw after...

The Snapmaker 2.0 CNC gets a boost from its vacuum attachment, which allows users to customize its height according to their needs. ...This innovative accessory attaches seamlessly to the CNC module using ultra-thin double-sided tape, ensuring a secure...

supporto per comparatore millesimale ancorato all'asse Z della stampante snapmaker 2.0 350. ... G.code da PrusaSlicer Al layer 99 pausa per inserimento dadi da 4 comparatore:...