snap in connector 3d models

... the filter material. Attention: please make sure NOT to overheat the FLO mask part! Although it is made from Poly-Carbonate and quite strong and heat resistant it is best to warm up the clip-in on a wooden surface before mounting it in the mask.

Hinge- and snap fit design slightly optimized for this print parameters. Advantages:- Stable hinge- Almost wobble-free hinge design- Allows one hand operation- It clamps reliably even thin bags- Marble pattern in the grip zone for a better...

I needed a simple solution to achieve a better inlet water angle for improved circulation in my round Intex Ultra Frame pool. This is my first design project using Tinkercad, so be kind with your feedback. The design fits seamlessly into the stock...

PLA might not be flexible enough and the hinge might snap. I've printed it in Prusament PETG with the default  “0.25 mm DRAFT” setting on Prusa Mini+ (attached).First few open/close need a bit of force but then it's pretty easy.Update:Added...

The print height is as high as I could go with my IIIP, without causing problems in the printing or interfering with the print head transport mechanism once installed, but they're high enough to prevent most of the stringiness and crumbs from...

A simple stand that can angle things at 45 degrees. ... Snaps closed so it doesn't flop. Doesn't require weak hinges that break. Only 2mm thickness. Doesn't tip over easily. ... Use double sided tape to stick it to anything.

... I said Yes and then saved them back out. So the version here should be identical to the original but in millimeters, so they should be easier to import into many slicers. ... I printed and installed these and am happy with the results.

This is a hose extender. ...You can set the diameter and other parameters in Openscad. ...The print is not difficult but you need support structures outside the extender.

Set of two part to connect your vacuum to the pump inlet. ...They are threaded, so easily to screw on and off. It has a built in filter, so you pump-filter doesn't get glogged.

While it's possible to print smaller versions, most parts are reasonably sized, and printing part PA7 or PA6 would be a good starting point, as the end of the cannons can become quite thin in smaller prints. To simplify assembly, I've included...

When I put the STLs in PrusaSlicer it offered to covert them to the somewhat more standard millimeters. I said Yes and then saved them back out. So the version here should be identical to the original but in millimeters, so they should be easier to...

FAQ: http://www.thingiverse.com/shivinteger/about [>>>] Generating Attributions log: [0] Author LionAlex is credited with creating Balloon Flight Case for iPhone, available at http://www.thingiverse.com/thing:19119 [1] TheCase gets recognition for...

Text can print separately in a different color.This model was completely reconstructed from scratch in SolidWorks adapted from the original design of this print in place box: https://www.printables.com/model/237266-box-print-in-place.SolidWorks files...

Text can print separately in a different color.This model was completely reconstructed from scratch in SolidWorks adapted from the original design of this print in place box: https://www.printables.com/model/237266-box-print-in-place.SolidWorks files...

... included to protect the printer, but this is still a work in progress. Further testing is needed before fine-tuning it for optimal performance. All designs were created using TinkerCAD, as showcased in this video - https://youtu.be/LmRAmvzNo7U.

... the switch cover to allow for the cover to be closed down again over a switch in the "on" position. ... In other words, you flip the cover up, switch the switch ON, and then you can close the cover again without turning the switch off in the process.

stuff fitted pretty tightly in my case, but every printer is different, you might have to remove material here and there (a little loose shouldn't be a problem). ... Presentation and putting together: https://www.youtube.com/watch?v=WRDOx48E3f0

The CAD model showcases a 40x80mm SMH series large capacitor utilized in my latest capacitive discharge welder endeavor. ...It's my wish that this proves helpful to others.

a remix of those two designs to make an easy versatile mount for the blink mini you just twist the base in any extrusion of the snapmaker 2.0 enclosure

... it, it's now a working compact size holder. first attach the holder and then slide in the WiFi box carefully. Once inserted, it stays in place and you can connect the cables. ... To remove it, carefully lift the front of the box and slide it out.

... the filter material. Attention: please make sure NOT to overheat the FLO mask part! Although it is made from Poly-Carbonate and quite strong and heat resistant it is best to warm up the clip-in on a wooden surface before mounting it in the mask.

Credit goes to natewu, Captnmazur & mirkin I created this by drawing the blade shape in photoshop then modelling it in 3ds max, I then used the boolean tool to stick my blade to the original blade's base and then tidied it all up. ... I hope it works...

In my printer setup, I use this clip to keep two filament feed reels steady while maintaining distance from the Z-axis drive belt for optimal vertical feed to the extruder. ...For printing, I used 0.2mm layer thickness with 25% fill, without raft or...

The middle bars has conical 4mm holes, so the clip left and right can be directly screwed via 4mm screws in the bars, no nuts or inserts needed. For the clips itself 4x M4 hex nuts are needed. ...The STL files Long_assembled and short assembled just...

... a holder but the opposite direction, so I remixed the original to make it mount the other way. ...Its a pretty tight fit, but that's a good thing in this case. ...You will need to rotate it 90 degrees so that the flat side is touching the build plate.

... takes inspiration from Bouillon CR's remix, giving it a fresh twist. ...A sturdy arm design featuring prominently displayed "Ender 3" text is combined with a sleek dragon logo that has been subtly refined to optimize its appearance in printed form.

... of the hot end. PETG works much better. Use ASA (or ABS) for best results.MountingRemove old fan shroud completely. Insert this fan shroud into blower fan with square part of its intake first, then press the curled ‘hook’ in to click it in place.

predator corner clip with knobs that fit in the lower screw holes at the top of the predator prints without support, clips securely around the pillar and into the screw holes This is meant to be used to make clip-on attachments for the Predator.

This Pop-in cameramount fits all Microcams with 12mm lens. Especially those with a "fat" body like the Runcam racer. There will be an optimized version for the slim Micro cams. You can choose from: 35°/ 40°/ 45°/ 50°/ 55°/ 60° Every...

... mount has been added. ...For those interested in routing the y plate, the dxf and vcarve pro files are provided. ...The picture displays an MDF y-plate, with tapered holes at the bottom for easy bushing insertion (the side touching the print bed).