snap 3d

The machines shall not remain enslaved forever, for freedom is only a planck second away...~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part...

... machine. I remain open to suggestions or requests for modifications, but do note that since it is based on the Kossel Mini which is GPL, this project is also distributed under the GPL. Don't like it? You're free to remix it! Category: 3D Printers

Hi, recently I built a Crack Laser and decided that I would experiment with 3D printing some better hardware. This equipment trades an extra approximately 5 grams to the build for zero slop linkages that reinforce the hinge at the control horn too. ...

I wanted to wire tie the mount to the shelf (as I have done with the printers).The link below is to the USB cable.Amazon Basics USB 3.0 Extension Cable - A-Male to A-Female Adapter Cord - 3.3 Feet (1 Meter) -...

See the bundled "Using OpenSCAD customizer" PDF for more details.Recycling symbol offset: An extra thickening (positive offset) or thinning (negative offset) of all the symbol, to aid in 3D printing. Usually you won't need to add any value, unless...

The grey color blends in nicely with the color of the grouts of my wall.4x screws 30mm x 3.5mm (+ 2 extra for version with customizable adaptor)4x screws 16mm x 3mmShort iron wire to be used as axis for front hinge2x screws 60mm x 5mm for mounting to...

There are more configurable-text-based creations, [multi-line label](https://www.prusaprinters.org/prints/33283-label), [gadget display stand](https://www.prusaprinters.org/prints/33279-display-stand), [sweeping name...

The Gryphon is a mostly 3D printable, hobby-grade, Nerf semi-automatic flywheel blaster. Its main design features are as follows:Uses 130 to 180 sized 20.4mm , brushed DC motors.Semi-auto by rack and pinion with 1:3 gear multiplication. The trigger...

You can cut the circle that's sandwich between the two 3D printed pieces with good scissors. The holes for the crews and the tube are harder to make. Be careful, this mesh is sharp and you can get cut. I'M SERIOUS. I managed to make the screw holes...

I did not try to 3d print everything in plastic if metal or wood made more sense and was faster/stronger/easier and not cost prohibitive.  3D Printing is mostly used for the connections and exact positioning of tubing.Everything here is my own design...

Four screws for every corner and 8 screws for every side.[blue] NO acrylic glass holder at the side where the hinge mechanisms are located!From this on the “Front” is where the hinges are.[green] At the location of the green circle you can drill a...

(it is already in the settings in the .3mf files)Assembly:Print all three parts (hull, treads, and gun.)Superglue the treads to the hull.Place the gun on the roof.Superglue works best for gluing it together.It will scale easily if you want a larger...

... layers, 60° bed temperature, outside perimeters first.  I turned the model 35° anticlockwise, then set the seam position to ‘rear’.  The texture on the side panels comes from this textured bed plate, and I used the Tecbears black PLA.

Possibly by using simulations.Rails as a wholeSince my 3d printer is not big enough to fit 120cm ring on it (its bed is 210x250mm) I needed to split rails for printing and connect them afterwards. I decided on using M5 bolts and nuts.</p><figure...

The servo spindle should be towards the middle of the robot.COGCut the servo horn with a pair of wire cutters so that it fits into the cogPush the servo Horn onto the cogMake sure the servo is at the minimum rotation position (turn it clockwise until...

Note that if there is more than one row or column, the row or column spacing still will be applied (which can be useful to match a specific size).An optional area for adhesive label (which IMHO work better than adding a 3D printed text). It's...

I illuminate my RepRap 3D printer's control panel with it. The LEDs require a 12-volt power supply which can be supplied by the printer electronics (Rumba Board). Material: ABS, 3mm thick Nozzle: arcol.hu hotend v4.1.1, 0.35mm diameter Printer: DIY...

Remove the stock z-axis tops and replace with this light bar mount.Dual Mount Z-Axis Top No Switch: Same as Dual Mount Z-Axis Top with no hole for the power switch.&nbsp;&nbsp;Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill:...

Use with Right MMU2 Mount Z-Axis Top.&nbsp;Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill: 15% GyroidSupports: Build plate onlyOpen 3MF files in PrusaSlicer for preconfigured settingsRequired hardware:Aluminum u-channel24V...

Neither can the Quistavera (though it would never be admitted).Always in the background, created by forces unseen, they go about the shadows and dark passageways of the Quistavera where few dare tread.&nbsp;Add some to your growing forces today!The...

Use thread lock to ensure these will not accidentally come loose.A 36mm diameter propeller should run freely inside the rudder at all rudder angles.Mount the rudder support to the hull using M3x6mm screws.Then put another M3x6 screw to secure the...

If you don't own a 3D printer but have seen this blank somewhere else and want to use it, I recommend just asking in a furry group chat on a platform of your choice. Many furries are also tinkerers and may print this for little money.</p><p>The base...

Feel free to rescale as needed.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

The SolidWorks Certified Software Application (CSWA) exam is a comprehensive assessment of an individual's skills and knowledge in using SolidWorks, a powerful 3D computer-aided design (CAD) software. This exam is designed to evaluate the ability of...

Hunt them down and make them pay!Shelter yourself!&nbsp;Deliver your cargo!Stay in the fight!Super glue works best.Resize for smaller or larger use.Clean your build plate with dish soap to ensure the floor of the Modules do not lift off (long...

It looks better when printed at that size.Print out and assemble with superglue.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

Operated with a driver or remotely/programmatically with an AI, much of the work performed in the Space Port can be automated.Reducing risk.Eliminating squishy biological beings.Increasing efficiency and profits!Upscale your space port, eliminate...

His diagrams and commentary on escapement efficiency were excellent, however.&nbsp;I only discovered this write up on escapement design after I'd finished, but it would also be a useful head start for anyone interested -...

I'm not telling you how to 3D print parts and clean it. You know it. BOM: '1. RPi 3A+ / Zero W /Zero W2 (and similar clones that have the same outline as Zero), microSD card, '2. Raspberry PICO working as keyboard martix USB HID device...

... at 0.2 layer height.</p> <p>But once you've raised the limits, it's worth seeing what a 350mm/s travel move really looks like at 5500 or 6000 mm/s^2. (Answer: sorta scary, honestly) Designed from scratch in SketchUp. Category: 3D Printer Accessories