smartthings hub v3 3d models

Feel free to do whatever you want with them.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

With the thermistor I use, I elected to retain the wiring on the right along with the wiring for the hotend fan (per the photos). I only had a Trianglelab's 3D Touch on hand to test this with rather than a BLTouch v3.0/3.1. Comparing the schematics...

Check the URL to connect to in your Arduino IDE serial monitor output after startupA short rainbow animation will be shown to check the function againNote: The animations used in step 1 and 5 can be switched off in the settings Video: Music credit:...

(As long as it's not printed in dark opaque filament.) Case_Rear V3.stl, Case_Rear_with_Ears V2.stl Case front Increased the width and depth of the separation between the logo and cooling slots. This is to make the logo stand out better and to make...

Adjust till its Parallel with the bed and then tighten the bolts back up. Printed Parts:MGN15H Mounts - Print in ABS+ or other structural PlasticPower Supply MountEnd-stop mounts x3Y End-stop BumpSpindle Speed Controller Panel Purchased...

The current Slic3r PE 1.41.3 stable will load the project file including the custom layer start gcode for the magnet insert, but will loose the filament changes. I printed this on my Original Prusa i3 MK3S with firmware 3.7.0-RC1. Pictures and videos...

What fun! To build an adapter to your requirements, install Blender v3.80 (or later) and open the T2M42atapter_pre_assembly.blend file. Select menu View | Front (or press number [1] key on the keypad) to view the model from the front against the...

You'll need these pieces: * MQ2 Smoke Sensor (https://www.ebay.fr/itm/MQ-2-MQ-3-MQ-4-Gas-Sensor-for-Arduino-Raspberry-Pi-Nano-Due-Uno) * DHT22 Temperature and Humidity Sensor...

This is the V3 version of my mod and it's second release. With this version compatibility with MK3S and MK2.5S have been added. The Z-Motor mounts have been updated inline with the Prusa R3 versions and cable management has been improved. If you have...

I made them on TinkerCad.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

V3 has the location of those back to the position of the original design. After dropping a spool on the original and breaking it, gluing it back together, and dropping the same spool twice more on it, I decided to make a new one. The original...

Dual filament spool holder for the Geeetech A10M using the rewind mechanism from the Universal Auto-Rewind Spool Holder (https://www.thingiverse.com/thing:3338467) made by Vincent Groenhuis, many thanks to him for making this :)\r\n\r\nI used the...

You could drill the holes but I'll fix this in v3. Also, the power plug, while still on top, still has its connectors sticking into the 80mm fan. I will either extend the back another 15mm to compensate or the user will have to bend the wires for...

If using the original 2 piece traps then the funnel hangar prints right way up without supports. Container specifications:MILK fits: 38mm neck Bericap (Milk jug containers - normally 0.568(1pt), 2.000, 2.273(4pt) 3.410(6pt) ltr capacity)COKE fits:...

UPDATE Replace the X Carriage and Part Cooler parts with V3. Minor tweaks to both. Adjusted the belt attachment on the X Carriage by moving to the back slightly to improve alignment with belt path. Increased the size of the end stop plat on the Part...

This is a small missile I built for use with a sci fy model. Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

This is a remix of @joeshmoe9898_813349 Spirographic WDT Tool  NOTE: I just played around the TOP and PIN file, you will need other original files from his project. Files you need from original project.Gear A V5.stlGear B V5.stlGear C V5.stlGear D...

### Changelog v3.0 - 12th Oct 2023 - Added first version for Raspberry Pi 4B, connector comes with or without a fan mount so you can accomodate your own custom cooling solutions since the RPi4 sometimes needs more juice. - It has been inspired...

Z-offset with V3 is about 1.5mm to the nozzle of a Volcano Block! But this is very dependent on the Bed Material! - Definitely won't fit standard V6 Blocks! - Step file for Mount is uploaded too. If you want to fork it for BL-Touch or something, just...

It is not necessary to make any changes to the firmware of the printer; I use currently V3.4.1-RC1 (English). The adapter consists of the following components: Housing top part in 3 variants, Housing lower part, Lid for the threaded inlet, 1 x...

Now you can print them out and use them for your nefarious purposes as you travel the far and vast star systems.The Original Galindos - https://www.printables.com/model/143724-galindos-robot-model-science-fiction Galindos Evolved -...

if you do test it, please post pictures and leave a comment.V3 mount has been tested and working on the SKR PRO V1.1==================Ribbon Cable Breakout PCB BoardBeefed up trace width where possible.Heater PCB trace has trace on both Front and...

Make sure it will bridge to the shortest side.the bottom case is a multicolor print with filament swaps, i used black for the main case, white for the not used body parts and Red for the body part the tracker is for, you can use whatever color...

Update V3: Ok so I didn't realize before I make an STL I should combine the parts into a single solid, then convert to STL. So some parts may print funky. Just fixed Battery tray, need to review other parts. Deleted a battery tray with exhaust that...

* BLTouch_Mount_Adjustable.stl * BLTouch_Mount_Slider.stl # Firmware ### Driver Connection to MS Windows via USB-Cable: CH34x_Install_Windows_v3_4.rar ### Display Display Firmware (TFT / TSC) from digant moded to Genius. When you want to use non...

You get the picture).Change the PLA type to the one you are using for best results.Designed on Tinkercad. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building...

Trouble is removing the whole fin assembly and migrating the electronics would take a while so I've designed V3 of the spacer which allows for modules to be swapped in by undoing 2 bolts. I would recommend diffusing the light a little since when...

An X server graphics environment is required and the build has been tested on debian and ubuntu.Setup openscad-amu (OpenSCAD automation and docgen tools)(shell commands)$ mkdir tmp$ cd tmp$ wget http://git.io/setup-amu.bash$ chmod +x setup-amu.bash$...

2018-09-23: V3 Since I've installed TMC2208 V1.0 stepper motor drivers, I had to rotate the connector plugs on the TRIGORILLA board by 180°. This rotated plug (especially the one for the x-axis) comes closer towards the pcb's edge and collides with...

Violence is never more than a heartbeat away.Keep your vehicles fueled!Stay in the fight!No support requiredResize for smaller or larger use. Designed on...