small spools 3d models

Customized version of https://www.thingiverse.com/thing:1782398 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1782398

Customized version of https://www.thingiverse.com/thing:45101 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=45101

Yet another earphones organizer is now in sight. This one has been designed to be as compact as possible, measuring a mere Ø 5cm in diameter and standing at just h 2cm tall. The design may not be the most aesthetically pleasing, but it's...

The human hand grasps a compact reel.

Tiny filament roll, designed specifically for utilizing leftover filament bits and testing out various filaments.

split the original to provide an stl for the small spool. ... original item print settings

To avoid scratches in the plastic part, mask the saw blade with tape where you do not cut.Remove burr and clean the parts from chips.Put both spool parts and clamping parts together, allign the parts and drill bores ⌀3mm (4x).Remove burr and clean...

To avoid scratches in the plastic part, mask the saw blade with tape where you do not cut.Remove burr and clean the parts from chips.Put both spool parts and clamping parts together, allign the parts and drill bores ⌀3mm (4x).Remove burr and clean...

To get a constant thickness of the spool, I recommend to use a piece of wood which fits to the inner of the spool to guide the saw blade (see picture).Make a cut in the piece of wood where you want to cut the spool. Clamp the spool in a vice.Use a...

This is a simple, small spool for coiling wire. Its total radius is 15mm but the radius of the inner part of the spool is 12.5mm. The inner part of the spool (in between the two sides) is 8mm wide and the two sides extend 2.5mm out and in from the...

Filament spool for small (0.25 kg) filament refills.

Artillery Hornet small diameter filament spool holder split in half

https://amzn.to/35Jgnc2 However, the spools don't fit on the stock Ender-3 V2 spool holder--the hole is too small. If only I had a 3D printer. WAIT - I do, I do have a 3D printer. So I picked up a cheap 1KG spool (which fits the stock spool holder),...

I ran in to a 40mm inner spool reel that is too small for the stock spool holder on my qidi x-PRO. ...So I made 1 to fit the 40mm spool hole

I have several small size filament spools with holes that don't fit the standard spool holder. This also will fit on any 20 x 20 extrusion frames with "T" nuts. I also needed to lower the overall height of the printer. ...This fits on the back side of...

Unfortunately, they had very small holes that wouldn't fit on the standard spool holder's original design, with the holes being roughly 17 or 18 millimeters in diameter. So, I rummaged through my toolbox and found a nut with threading from ChunkAhoy,...

This compact holder can accommodate spools as small as 1.25 inches and features a retention mechanism for added security. It's specifically designed as a quick replacement for standard Makerbot spool holders, versions 2 and 2X. The second file...

Just another Ender S1 spool holder that can used with spools with smaller holes

Works with the stock Ender 3 / Ender 3 Pro spool holder retention nut Intended to be used with filament spools with smaller openings than the standard 1kg spools

Shorter spool to take out some of the slop and extra. ... Fits up to 1kg spools or up to 2 5/8" wide. Tip is 1" Shaft is 7/8" 1/8" lip to keep spool from sliding off

this to hold an exterior spool of filament that has a 1.25" hole in the spool. ...You will need to print using supports

A custom spool holder tailored to fit the compact Tauulman spools, specifically designed for use with a Sigma printer. ...Simply print this design without any additional supports.

With this adapter, users are able to utilize the compact Flashforge spools or employ it to securely store two spools simultaneously.

The Mini Spool D120 accommodates 50-100g filament, designed in SolidWorks. ...It features an outer diameter of 120mm and an inner diameter of 100mm, with a spool length of 25mm. ...Enjoy your printing experience!

A compact replica of a basic side filament spool stand designed specifically to fit alongside a Flashforge Dreamer 3D printer.

This wire spool is resizable, you can print without support and join both parts with super glue/ soldering iron.

I designed this spool arm specifically for smaller diameter filament spools like Dremel PLA. It fits perfectly into the slot on my Monoprice Select Mini, just like the default arm that comes with it. This was one of my first DIY projects, and though...

I created a custom spool holder for my Ender 3 Pro because the standard one wouldn't accommodate some of my larger spools. ...As a beginner in the 3D printing community, I designed this smaller version myself as a learning experience.

For me, that solution is a compact bolt-on spool holder specifically tailored to accommodate the tight fit of spools featuring narrow holes - mere 3 mm in diameter, to be exact. ...Its sleek design requires minimal 3mm bolts for seamless assembly,...

This is a specialized filament clip designed specifically for clipping filament onto compact Amolen brand spools. After experimentation, I discovered that universal clips often fail to secure tightly to this particular type of spool. ... Version 1...