small jetboat 3d models

This is a super fun boat your kid can play with in the pool or bathtub right now! ... Print Settings Printer: Creality Ender 3 Rafts: No Supports: No Resolution: 0.3mm Infill: 30%

First-hand drawing hope everyone does not criticize

This Custom Speed Boat is a reinvented version inspired by the outstanding work of wersy, I suggest checking out his build instructions first! : http://www.thingiverse.com/thing:930577 Speed Boat 3 RC This design remake incorporates jet propulsion...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Jetboat using a 3D printed propulsion system

This is the first version of my 3d printable Jetboat. It will be updated/improved soon! New version will have all the parts which are perhaps missing again in this version! Needed material - 400g of material of your choice (350g hull / + Jetpump...

... float with this motor. ====================================================== Motor for rc JETboat 3d printed https://www.youtube.com/watch?v=hlDM29kybuk ====================================================== JET_motor.zip.txt rename JET_motor.zip

See this boat running on White Rock Lake here!https://www.youtube.com/watch?v=Du9jIz9oGyM&list=PL0_RdX5Eqj9RK30akJnr1RCpg6ZdFCJtE This is a huge 3D printed jetboat that is printable on any print bed that uses a 220 x220 x 250 print bed. Take a look...

During printing, add some PVA glue where you see small gaps to the support structure, this will hold during printing and break away perfectly after printing. When slicing, review all layers before starting the print if you scale or print with an...

There is also a small print that is for the water inlet side that is on the bottom of the boat. So far I have only done a test in a tub but when I get the boat out on a larger body of water I will add it here. I did also cut up and put pieces of a...

This is my first time modeling a boat, I'm trying to build a jetboat this summer and figured modeling it /printing a couple times to test the hydrodynamics Any recommendations on things to change would be greatly appreciated, ordering the aluminum...

Yes once built propetly but i strongly recommend covering the circuits with nail varnish or a dedicated protective product, put the battery in a small waterbaloons and keep a piece of sponge inside the hull. Water protection spray for electronics...

The esc is a slide fit with a small stop lip at one end ( Not sure if I got a faulty one, they are junk, or I'm pulling way more than 90a but I'd say buy esc at your own risk because mine melted down and caused burn damage to my hull.) UPDATE: I've...

customized with 3D Slash!

I've installed a replacement impeller for the NQD jet drive and tested it in a bucket of water, achieving great success. Next, I'll thoroughly test its performance. The new impeller fits snugly onto the standard shaft with precision. For printing, I...

This is my latest stepped hull, a work in progress. Lots of advantages come with the steps and specific tile orientations that affect boat handling behavior. I'll be CNC routing a model and creating a mold from the model. Stay tuned for updates. I...

This hull works with all the parts of this model:https://www.printables.com/model/51680-3d-printed-rc-jet-boat/comments/897854https://youtu.be/-7sSGXb9A3U?si=2WvybAz3n-ELLGuwjet housing is included in this model.The deck has to be splittend in the...

Finally I've finished it... and assemble. will publish a video later, when test on the big water. My shell's split with guides for correct assembling. Used 2mm carbon tubes or even toothpick should be ok. Length is about 10mm, better use 9. +...

A compact vessel cradle for a diminutive watercraft, specifically designed to support the RC Mini Jet Boat model found on Cults3D. ...Six M2 x 8 bolts are recommended for secure fastening.

Update 14.03.2024 Supersprint V0.1: A quick small patch. An issue with too low wall thickness on hull middle in front left part of the lid interface was fixed - thanks San Xu for reporting this. An instruction about ESC placement was added into the...

Boat hull height is approximately 350 millimeters, with a maximum limit of 400 millimeters set by the cr-10 printer.\r\n\r\nTonight's print attempt will aim for identical results as full-scale printing, thanks to careful cutting of the nose off in...

Secure your components by attaching the battery holder, receiver, and ESC to the hull's underside using strong double-sided tape. ...Keep the battery snug in place with velcro straps, while the receiver and ESC stay firmly anchored with adhesive-backed...

Remote controlled jet boat, designed for easy print and assembly. No supports needed and selected electronics for a fun, fast, but cheap build. Instructions including BOM list, STEP and STL files are included in ZIP-file. ... Uses ~380 grams of...

After dealing with water flooding my boat repeatedly, I created these parts for my NQD Tear Into Jet Boat. The design includes a 2mm plexiglass component featuring six locks to ensure a secure seal. To make the process easier, I designed two wrenches...

Small - a collection of beautiful shapes reflecting cute creatures and objects

http://www.thingiverse.com/apps/customizer/run?thing_id=74322 Instructions Using the following options: picture_shape = square hole_diameter = 10 text_reverse = no text_size = 10 image_file = lithopane_new20160204-25020-vhbt8v-0.dat...

Human-Crafted Version of Thingiverse Object: http://www.thingiverse.com/thing:56257 Created Using Customizer App: http://www.thingiverse.com/apps/customizer/run?thing_id=56257 | | Instructions Using These Specific Options: text = Miniature Size...

Using the following options: lug_length = 4 border_color = Black outline_thickness = 3.0 line_spacing = 1.4 inner_margin_width = 1 text_color = DarkRed outlineextruder = extruder1 font_narrow_widen = 0 ruler_unit = 10 outline_color = Gray...

Human: Spinner of small stature (diameter 70mm).\n\nFor use with bearing 608 (22 X 8 X 7 mm) and nut M8\nPrinting the body requires no special instructions, but covers must be printed with symbols facing upwards and supported.\nThe bearing, nuts,...

Small reel. Sides are printed on both sides of the reel. A central plastic plate, measuring 3 mm thick and made from caroplast material, is inserted into each side part. The layer thickness for printing is set at a mere 0.1 millimeters. The hull...