slotted strut channel 3d models

Low profile is 13/16" high x 1-5/8" wide. ...Uses same tee nuts and mounting bracket hardware as 1-5/8" high channels.

Slotted 1-5/8" strut channel for Rigid/IMC/EMT conduit mounts. Different lengths in .sldprt and .step formats. 6'8" length is used for beams spaced 6 ft apart. The length allows 4" on each end to attach the channel to the beam. ...Also called “unicanal”...

This is a standard strut channel featuring precision-drilled holes, all measurements adhere to the specifications provided by our supplier.

Unistrut, SuperStrut, Metstrut, Kindorf, and Strut Channel represent identical products worldwide. In the US, it features a 1 5/8 x 1 5/8 square with 9/16 holes spaced 1 7/8 inches apart, while globally it's known as a 41mm x 41mm structure with 14mm...

strut channel floor mount

A simple strut channel closure strip

Mounting bracket for 1-5/8" strut channel. ...Clearance holes for 3/8-16 bolt.

This is a simple strut channel closure strip. ...10" long, but can be customized as needed.

Tee shaped mounting bracket for 1-5/8" strut channels. ...Clearance holes for 3/8-16 bolt.

L shaped mounting bracket for 1-5/8" strut channels. ...Clearance holes for 3/8-16 bolt.

lowpro strut

Trolley has a vertical plate with holes for attaching hooks and shackles. ...Slides inside 1-5/8" strut channel. ...Wheels roll along inner lips of channel "J" profile.

45 degree brace supports two legs of 1-5/8" strut channel joint. ...Use 2x 3/8-16 bolts and channel nuts to secure.

Trolley has a vertical plate with holes for attaching hooks and shackles. ...Slides inside 1-5/8" strut channel. ...Wheels roll along inner lips of channel "J" profile.

A simple strut channel closure for unistrut strut channel. To install, butt the long edge of the strip and press inward at the opposite long edge, near the clips. It will flex and snap into place. Purely cosmetic. ...I use it to hide wires in my...

Mount a length of strut channel between the sides of a beam to run cable and conduit along the beam without drilling. Position the mounts at either end of a piece of strut channel that is 1" to 1-1/2" shorter than your beam opening. Turn the bolt on...

StrutCapInternal is designed to fit snugly inside a standard 1.625" electrical strut channel, while StrutCapExternal1 attaches directly to the outside of this same size channel. Meanwhile, StrutCapExternal2 covers a slightly smaller channel...

... The trolley also has a hole in the center to accommodate an 8mm bolt. In my application, the strut channel is mounted on the ceiling and the trolley rides on the rails. ...The center hole allows me to bolt a hook from the bottom of the trolley.

Inside channel width is 1-5/8" x 3" high. ...4" x 6" x 1/4" thick floor plate has two 3/4" dia holes, 4" on center.

Inside channel width is 1-5/8" x 3" high. ...4" x 6" x 1/4" thick floor plate has two 3/4" dia holes, 4" on center.

Clamp supports 1-5/8" strut channel at a right angle to the beam. ... Has two plates on the bottom that slide into the strut channel and a lock nut to secure the mount. ...A threaded hole on the bottom supports 3/8-16 threaded rod.

Clamp supports 1-5/8" strut channel at a right angle to the beam. ... Has two plates on the bottom that slide into the strut channel and a lock nut to secure the mount. ...A threaded hole on the bottom supports 3/8-16 threaded rod.

This is a strut shelf mount with: 3 ea) holes for 1/4"-20 bolts and strut washers to be secured to the strut 2 ea) #16 screws to attach the shelf It is designed for a 1-5/8" strut channel and is intended to be installed with the small rib to be...

Mounts 1-5/8" strut channel to I-beam with 3/8-16 bolt and channel nut.

Mounts 1-5/8" strut channel to I-beam with 3/8-16 bolt and channel nut.

Mounts 1-5/8" strut channel to I-beam with u-bolt. ...Clamps to bottom leg without drilling into web.

Mounts 1-5/8" strut channel to I-beam with u-bolt. ...Clamps to bottom leg without drilling into web.

Mounts to 1-5/8" strut channel with 3/8-16 bolts. ...Extended tab on short leg restrains bracket from moving due to rotational loads.

Mounts to 1-5/8" strut channel with 3/8-16 bolts. ...Extended tab on short leg restrains bracket from moving due to rotational loads.

Goes into 1-5/8" strut channel. ...Radius edges allow nut to be installed through gap and rotate 90 deg to hold nut on two grooves.