sliding bracket mount 3d models

This bracket enables gamer to hold Sony Dualsense gamepad and PS Vita together. It is better to look at this tiny screen closer to eyes. Holding gamepad under Vita is also convenient. There are hole for charging cable. ...Rear camera can be used too...

Wall brackets sized to hold filament spools with 1" dowels. Screw holes sized for ANSI #8 screws. I printed mine with 20% gyroid infill and three shells. Does not require supports. ... Use drywall anchors if not screwing directly into wall studs.

This mount will give about .050" clearance between the top of the amp and the mount surface, to allow for airflow. I have included two versions.For those that don't mind seeing the mount and want more strength select the mm_amp_mount2.stl file. ...Those...

I used an USB hub from Logilink for my Octoprint setup on my 3d printer. ...To mount it under my cabinet I created this holder. Just use some countersink screws to mount it somewhere.

To enhance my existing 3D scanning setup using a tripod, I developed an idea that incorporates an off-the-shelf shower sliding bar with a standard shelving unit back support, allowing for vertical adjustment while keeping the entire build compact...

Stepper motor hole has been enlarged to 23mm to allow stepper bezel to fit through the mounting hole.

EKWB Water Pump mount for 120mm radiator Print instructionsPETG, 0.24mm, nothing special

Holder Height: Resolution: Clasp Clearance: 2mm Guard Width: 0 Mount Hole Diameter: 3mm Mount Thickness: 3mm Count: 6 pieces Fastener Type: Standard #180 screw Clasp Thickness: 2mm Counter-Sink Hole: None Clasp Arc Radius: 250 degrees Guard Depth:...

... TO ABOUT -1.38 MM FROM BED. ... TO BE SAFE I WOULD SET IT A LITTLE HIGHER AND ADJUST AS NEEDED. HOLD THE MOUNT FIRMLY AGAINST THE METAL MOUNT WHILE TIGHTENING THE BOLT SO THERE ARE NO GAPS BETWEEN THEM. SEND A MESSAGE IF YOU NEED HELP. ...

Mounts a compact display to your slatwall system, perfect for smaller monitors. Designed for lighter loads, it surprisingly supports a significant weight when printed with 40-50% infill density. Suitable for standard 100mm VESA mounting patterns. For...

Actually, the solution may well be used for any other use case since I simply edited @kai model and made it more suited for a broad application: removed unnecessary small holes in the base section; added one large hole to the base section, suitable...

Actually, the solution may well be used for any other use case since I simply edited @kai model and made it more suited for a broad application: - removed unnecessary small holes in the base section; - added one large hole to the base section,...

The bracket is specifically engineered to relocate the extruder from the Z-axis to the top support.\r\n\r\nThis design incorporates a filament guide that helps alleviate some of the tension on the extruder. ...To create this feature, I employed a short...

I'd like to suggest a creative way to reuse this thing - we could attach it to my pegmount bracket or repurpose it as a desk stand. If our printer supports this feature, I highly recommend using black filament for the base and adding a thin colored...

... effectively in holding up my 10-foot and 4-foot fiberglass ladders. The stepped recess (where the curves are positioned) holds the plastic reinforcement on top of the ladder, preventing the ladder from shifting left to right on the bracket.

... E3D hotend to your printer. Measure the distance from the nozzle tip to the bottom of the front E3D mount and redesign the mount and holes of it according to your dimensions. ...Don't forget that the BLTouch's standard nozzle dimension is 8.3mm.

This is a versatile base for mounting a high-definition zoom microscope camera onto an adjustable boom microphone stand, allowing for precise positioning and optimal viewing angles.

Mount a compact clip onto the outside to securely hold the feeder motor in place. ... Print Settings: Raft Configuration: Ignore Raft Support when designing your print.

A simple wall mounted Screw on Clip, It's very strong if printed with 4 walls and is designed to be an easy print with no supports.

This is a Paneldue 7i mount used on a Railcore 300ZLT. ... The Fusion 360 file has been included so that you can customize this for your own application.

Installing a surface mount for round pipe or conduit involves tracing its specifications from trusted sources such as Trace Parts Online.

Shadow board mount for Kincrome key set. Suits 9 piece metrix set. ... As per : https://www.kincrome.com.au/key-wrench-set-9pce-metric?SearchId=5216855&SearchPos=9

This is a BT-Q818XT pocket case designed specifically for a go-kart transponder bracket. Using this pocket case enables you to run safely with a cable tie. No additional supports are required, just ensure that you use a suitable plastic material such...

I fixed my DJI Inspire drone's broken bracket while still airborne and rather than purchasing an entire new stabilizing component, I redesigned the damaged part to be manufactured via 3D printing technology. This customized component performs...

All you need is: PTFE Tube PC4-M6 Pneumatic Fitting (Hotend pneumatic fitting) A printer with a 2020 Profile frame Print Settings: Filament - Any Filament Layer Height - 0.2 mmPerimeters - 2+ perimeters Infil - 10%+ Supports - NoBrim -...

Just a funny little wall-mount for the USB-charger of my wife. ... The charger mounted here is 120 mm x 61 mm x 26,5 mm I added the FreeCAD-file so you can change to your needs it if you like.

This VESA compliant mount is designed for televisions and display devices with adjustable hole patterns ranging from 75x75 to 400x400, supporting M4, M6, and M8 machine screws. It offers tilting capabilities of +/- 8.5 degrees up or down, or sideways...

This sleek 45-degree angle mount boasts a sturdy foundation rooted in the versatile Modular Mount System. ...To achieve the perfect balance, I carefully replicated the beveling found in its predecessor while incorporating a crucial 45-degree twist,...

... monitor on the wall, accommodating screens up to 22" in size. ...The sturdy mount is specifically engineered to fit a VESA 100x100 bolt pattern, securely fastened with high-quality M5 screws, ensuring a stable and reliable viewing experience.

I used https://www.thingiverse.com/thing:3260309 to mount a second extruder to the top of my Elegoo Neptune 2s, but I needed a way to mount a Creality filament sensor in a way that the filament could easily flow into the extruder. ...