slider fidget toy 3d models

I found the sliders fidget toys online rather expensive, just another thing to the list that your 3d printer can help you with.

Very small and addictive slider fidget. Slider 'snaps' back and forth into each end, allowing hours of mindless motion.The sides of the base are contoured for a comfortable hold with your fingers. Magnets are used to give a nice snap into each...

Press 5mm x 2mm magnets into the holes. A well tuned printer should leave the holes snug enough to hold them without adhesive. A tip for installation is to use your long stack of magnets and a small dead blow or non marring mallet to tap the lowest...

This is a model derived from the Emmet bearing it uses two of them with some gear teeth to create satisfying sliding motion when used right.

Fidget Toys Magnet Slider

print with a transparent and put glow stick or powder in it.

Print out a message on a transparent sheet of paper and sprinkle glow-in-the-dark powder over it to create an eerie effect.

25x50 mm tiles, topside ringed with .3mm depressions with the middle section raised .2mm, underside fitted .79 mm depression, fitted for 4 magnets. ...22.225x9.525mm each (44.45x19.05mm depression).to add magnet, use strong adhesive and magnet that is...

It has lines on the top that allow for smoother sliding that i saw in JamesThePrinter's slider (https://www.printables.com/model/140963-slider-fidget-toy) and they work great. Also added new sliders that go inwards instead of outwards if you'd like...

The toy's compact size makes it easy to take on the go, and with several interchangeable parts to choose from, including sliders and lids, you can customize your Fidget Slider to suit your unique style. We've included everything you need to get...

Fun clicky fidget toy. It slides! It turns! ...Requires 9 6X3mm magnets.

I just added an extra grip to the slider. ...It fits in by angling the part into the original and gluing as before. The extra grip makes the fidget much more comfortable.

A customizable, satisfying fidget and haptic slider with satisfying sound. There are three different styles in the files and because of the F3D files, you are able to add a personal design to your slider. You will need 24 round 0.5 cm times 0.1 cm...

A Pocket-Sized Puzzle Box. ... Inspired by the mind-bending creativity of Make Anything, this tiny puzzle box is a marvel of twisted toy design.

I saw this fidget design on AliExpress and decided to make one that could be 3Dprinted. Besides magnets, it doesn't use any hardware. You'll need 11 neodymium magnets (12 for 5x1 version) to make it work, and I made 3 versions: - 5x3mm magnets -...

A satisfying slider that makes a noticeable clicking sound while you push it up and down! Note! You have to turn on supports because some parts need to be printed to perform optimally. Is the spring not good? Too soft or too hard? Try printing to...

Toy Fidgeter

A simple fidget toy

This little fidget toy demonstrates a rack and pinion gear that converts oscillating linear motion into continuous rotary motion. Lots of fun with just around 2m of filament. Assembly Slide the sleeve over the outer slider with the small tab facing...

Fidget Explorer (V2) Innovated from Make Anything's popular fidget toy design.

This is a custom made Gear Fidget toy. ...Happy printing.

Simple Fidget Toy Mutter 100 infill Rest 20-30 infill

If you are looking for a fidget toy then I got the fidget toy for you. The fidget toy works by spinning the inner cylinder. ...The distance between the main body and the inner cylinder is 0.5mm (0.019in).

You're just an average fidget toy, scaled down to fit perfectly in smaller hands.

Rolling Fidget Toy: A Small Device Designed to Provide Relief Through Finger Motion.

Fidget toy 3 pieces Print Settings: 3 Walls 4 Top 4 Bottom 20 % infill

Fun little fidget toy for busy fingers. Printed at 70% scale, which worked well for me. ...Created in Tinkercad.

Fidget toy The coolest fidget toy ever. ...Are u nervous are u stressed no problem anymore with this fidget toy!The print is very easy and should not take more than 1 hour.

Fun fidget toy, designed in Fusion 360.Required parts:1 x Fidget top.1 x Fidget bottom.2 x Fidget gear.2 x 608 bearing.Bearing I used: https://amzn.to/2Adnn50. Print settings:Ultimaker 2+, Layer height 0.1 mm, 2 walls, 3 for gears, Infill 100%, 20%...

Tiny fidget slider that uses 5x1mm embedded magnets and with hexagonal pattern on top to add some grip.It can be printed in below 30 minutes and uses about 1.2m of filament.