skywatcher 130 pds 3d models
11487 3d models found related to skywatcher 130 pds.
thingiverse
I designed a larger focuser knob for my Skywatcher 90/900 refractor. ...It is easier to focus, and less wobble.
thingiverse
A simple hood to put on front of your Skywatcher 9x50 finderscope to avoid condensation. ... Easy to put and remove.
thingiverse
This is an addition to the stock focuser of many Skywatcher dobsonians. ...The extra diameter allows for somewhat finer focus control.
thingiverse
It is the little project that I was working on to make my Skywatcher 150750 EAF-compatible with my Astroberry. ...Inspired by Astroberry Focusor: https://github.com/rkaczorek/astroberry-diy
thingiverse
Designed this Bathinov for a Skywatcher ED80. The cap is slightly larger than the tube. Add some electrical tape on thi inside. This makes it fit snugly without scratching the tube during repeated usage. ...
thingiverse
This is a designed Bahtinov Mask for the Skywatcher Evolux 62ED used in conjuction with the optically matched 0.9x Flattener and Reducer which decreases the f/l to 360, f5.8 The mask fits over the dew shield.
thingiverse
Gear Train for SkyWatcher ED80 Focuser Replacement Internal Size 1.69 inches GT2 Belt Drive Application to Automate Telescope Focus Made from Durable ABS Plastic (235-250 degrees Fahrenheit)
cults3d
A cover lid for Skywatcher evostar 72ED. I didnt like the original screw lid because of metal dust falling on lens so I made a lid instead! ... I hope you like it =)
thingiverse
This is a t-shirt holder for shooting flats for a Skywatcher 72ED (72mm). ...up to four t-shirts can be sandwiched to make perfect flats, especially when incorporated with an ASIAIR.
cults3d
......It uses the same dimensions as the standard Skywatcher dustcap that comes with the telescope. The .stl is completely manifold and thus perfectly printable. It would honestly make my day if you could maybe rate or even upload a picture of the print.
thingiverse
... *almost* all slop/play in the connection. I am not sure if other Skywatcher mounts have the same size parts as I'm only new to astronomy but I suspect this will work with similar mounts like the HEQ5 and some other Skywatcher/Synta/Saxon mounts.
cults3d
... almost all slop/play in the connection. I am not sure if other Skywatcher mounts have the same size parts as I'm only new to astronomy but I suspect this will work with similar mounts like the HEQ5 and some other Skywatcher/Synta/Saxon mounts.
thingiverse
Mine is the eq-35i but I believe the lower mount is the same for the skywatcher eq5/6. This should also work for quiter2 Tiny PC MeLE Fanless Mini PC Quieter3Q...
thingiverse
I remixed an excellent design from "otherthing" to fit my SkyWatcher perfectly, as the original was slightly oversized when I printed it, likely due to printer scaling rather than any issue with the design itself. ...If you find this version too loose...
thingiverse
I need a replacement knob for the 6mm D-shaped shaft on my Skywatcher EQ5 telescope mount. I'm looking at version one, which is slightly larger than the original and requires some effort to remove due to its snug fit. ... However, I've also found...
thingiverse
Si tratta di un piedino specifico per il treppiede dello Skywatcher Mak 127 AZgoto da incastrare in quello esistente che ha un terminale a punta. Con questo, che ha la base circolare, sopra una pavimentazione liscia da più stabilità al telescopio.
prusaprinters
Using the same dimensions as the standard Skywatcher dustcap.The .stl is completely manifold and thus perfectly printable.tested settings with PETG:layer height: 0.3mm2 perimeter shellsinfill: 20%no supports needed
thingiverse
Focuser for Skywatcher Mak127 telescope. I chose a design that can be dismantled very easily. The housing is mounted on the dovetail while the big wheel is simply pushed on the focus wheel. The engine is a 28byj-48. ...The driver is an uln2003 The...
thingiverse
The motor system for the Skywatcher 200/800 telescope is a key component of its overall functionality. At its core, this setup utilizes a high-performance NEMA 14 HS-13 motor, renowned for its reliability and precision. ...To bring this system to life,...
thingiverse
......I used parameters that should work for a Skywatcher Evostar 120ED telescope. I printed the part for free at my local library and it worked just fine. ...It does fit a little tight, so if I were to make it again, I would make it 0.5mm larger diameter.
thingiverse
A custom-made cover lid for my trusty Skywatcher Evostar 72ED telescope. The stock screw lid just wasn't cutting it - every time I used it, metal shavings would fall onto the lens, causing a real nuisance. ...So, I decided to take matters into my own...
thingiverse
- SkyWatcher Heritage 150 modification: - motorizing the ALT/AZ axis for automatic pointing and star tracking, - motorising by using the 3d printed parts, bearings and 2GT belts used commonly in 3d printers, - adding the electronic for full...
prusaprinters
When polar aligning the azimuth adjustment screws would often just shift the whole head to the side rather than rotating it, making fine adjustments difficult and actually reducing the useful range of adjustment This bushing almost fills the gap...