skyscraper model

It is the smallest of the rounded moons of Uranus, about the size of Mimas or Enceladus, of the Saturn System.Type: Satellite. Orbit: Uranus. Orbital period: 1.413 d. Composition: Icy body. Density: 1.2 g/cm3. Dimensions: 480...

I made this trap to prevent those pests from killing the bees in my garden if they ever come close. I collected information, examined several models, made by individuals and professionals. This is my version. If you feel it is inspired by something...

Anyways, this is getting out of hand so here's the important stuff: Many models to choose from! 18mm sensor 12mm sensor 8mm sensor Then choose you cap: 2 stock fans with chain mount 2 stock fans no chain mount No fans no chain mount No...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Anyways, this is getting out of hand so here's the important stuff: Many models to choose from! No sensor mount 18mm sensor 12mm sensor 8mm sensor Then choose you cap: 2 stock fans with chain mount 2 stock fans no chain mount No fans no...

The picture of my working bitx40 model does not have the SPEAKER MIC wired up yet -still waiting for 2.5mm stereo jack. Files and features are subject to CHANGE. I will attempt to post relevant details with revision bumps as they occur. Also,...

... differences. As always please share any thoughts or feedback for further discussion and help each other move forward in design solutions, modifications for use on 3d printers like this model. ...These files were originally made with Tinkercad too.

This model was almost perfect, but when I printed one out, it turned out to be a bit chunkier than I really wanted. So, I figured I'd take my own shot at it and came up with this. My requirements were: * It had to match an authentic full-size...

Found a simple hip flask just laying about USHip flask discovered seemingly abandoned USHip flask uncovered, left behind USHip flask in basic design chanced upon USHip flask, a basic model, was stumbled upon USHip flask, plainly designed, was located...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

But don't hesitate to choose the one you prefer.The Raspberry Pi racks I designed are compatible with the Raspberry Pi 2B, 3B and 3B+ models. They should also be compatible with the 4B versions of Raspberry Pi, but I haven't been able to test them...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

This was a fun project but before starting, I recommend you read the 3D model description and 3D print settings. Also refer to all the attached photos. In addition to having a 3D printer and filament, below is a list of tools/products that I used to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

I used this here: https://de.banggood.com/Remo-B5509-Ball-Bearings-593mm-For-1621-1625-1631-1635-1651-1655-RC-Vehicle-Models-p-1450586.html - 9x M3 30mm screws and nuts to conetc top and bottom trays - otionally: 9x M3 0.5mm washers to put between...

Link to Coin: https://cults3d.com/en/3d-model/game/bugbear-d-d-set-d-d-minis-d-d-miniatures-d-d-bugbear-coin-token-miniature-dungeons-and-dragons-evil-pg Link to Full set: TBD(to be defined) Link to Coin set: TBD Link to Token set: TBD Link to Coin...

(The toothbrush still shouldn't fall out, but a hole any larger and it might...)(I also use a print of the original model as a holder for fine detail paintbrushes, so a hole in the bottom of that one would be rather pointless.)Enjoy!Print...

Larger or smaller screws can be used if you scale the model accordingly e.g. M3x8 screws at 150% part scale. Note: it's cheaper per screw if you buy in bulk from a specialist supplier. There are two versions of the container available, the standard...

Warning: At time of publishing this model is untested with an actual whambam3d build plate. Be careful to read all instructions before you start and follow them as written. You can damage your 3d printer if you are careless</p><p>The WhamBam3d...

**This is demo model meant to portray the scale and detail of the helmet itself** **For the full separated files as well as assembly videos, you can find them here** https://www.aguilarworkshop.com/product-page/scout-helmet-w-attachments Major...

Perfect for storing jewelry, electronic parts, cables, Lego models, tools, and other small items, the Pyramid Stacker offers a practical solution for keeping your belongings organized and within reach. By stacking the layers, you can store smaller...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

-Number of facets causes extreme delay in saving/rendering model, likely due to me not understanding the correct scad approach; I am still learning, feel free to leave me any feedback so I can improve my techniques. -Flat ring design (just like the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

The idea is to loose both heat breaks, push both nozzles into the bed, then tighten the screws in both hotends to secure the heat breaks.CreditsCM3D MK3S: https://github.com/ComunidadMaker3D/CM3D-MK3SMK3...

This model is designed for pla/pet-g which does not shrink. 2) print in the orientation show in the pictures. While this does not give you 90° opposition for force vs layer lines, it does give you about 45° which is much better than 0° printing with...

The color thicknesses and the width of the outline stripes on this test print match the stripes on this case and future cases I upload will probably use similar...

PLEASE WATCH &nbsp;THE HOW TO VIDEO ON THE BOTTOM OF THE PAGE!!There is a very important step many people miss out on and like that the Lifesaver is not correctly &nbsp;mounted into the case and will fall out eventually.The upper and lower lip needs...