sky watcher 8 dobsonian telescope 3d models

Make your sky watcher goto + track for around $200A hybrid of many of the onstep projects but without having to cut a larger hole in the base of the sky-watcher.Parts needed:onstep board: in my case a fsyetc e4 - preprogrammed...

A few upgrade parts for the Sky-Watcher Flex 200P dobsonian telescope: ball bearing hub: A 6 arms hub to upgrade the dobsonian base with ball bearings bottom sleve: A sleve to properly center the M10 screw in the 14mm hole slide sleve: The same...

Thanks to ProsperGuy, I was able to convert my Sky-Watcher 200P 8" Dobsonian to GoTo using OnStep. Files have been modded to fit the 200P dob. ...The rest of the required files are found on his thingy here: https://www.thingiverse.com/thing:3942813

Used 1.2mm for top, bottom and walls in Cura, printing with a temperature of 50C and 210C generic PLA. ...Employed clamps and slot spacing guidelines found on https://www.thingiverse.com/thing:801039 to ensure a perfect fit for an iPhone 6 housed within...

This focuser also fits other telescopes similar to the SkyWatcher Discovery 150p. They use the same poor focusing cheap mechanism and it can be replaced with this one! The project is not easy at all!!! It will probably take you 2-3 tries to get...

It uses components available in any hardware store, a set of two telescope mirrors and some 3d printed pieces. F=750mm D=150mm F/D=5 This was a 2020 summer project, it took me a lot of time. I do not recomment you to use this design (it takes...

Solar Filter for Sky-Watcher Newton 150/750mm telescope use with BAADER AstroSolar Safety Film (OD 5.0) or BAADER AstroSolar PHOTO Film (OD 3.8) Use a tap to create a thread for screw FreeCad source Category: Other

Create a Solar Filter for Your Sky-Watcher Newton 150/750mm Telescope Use the BAADER AstroSolar Safety Film with an optical density of 5.0 or the BAADER AstroSolar PHOTO Film with an optical density of 3.8. Before attaching the filter, use a tap to...

I have an 8" Skywatcher 200p Dobsonian telescope and wanted to add a fan to speed the cooling of the mirror and help reduce frost build up in use. The Skywatcher doesn't have any easy way to attach a fan and I wanted to use a USB charger rather...

GoPro 7 Sky Watcher - Flexible Material, 100% Fill Rate.

This is a manual movement knob for the Sky-Watcher HEQ-5 mount. To use it, you'll need to apply some force to slide it onto the shaft. For more detail, please refer to the accompanying pictures. If you encounter an "object is not manifold" error...

I modified a model: https://www.thingiverse.com/thing:160391 to fit my Sky-Watcher 200mm perfectly. The mask itself measures about 190mm due to printer limitations, but it works flawlessly. A central peg is designed to slide into the screw gap at the...

NOTE = THIS PROJECT IS ONLY SUITABLE FOR A SKYMAX 127 AND ZWO EAF WHERE THE DOVETAIL BAR IS ON THE SAME SIDE AS THE FOCUSING KNOBFeatures:A simple to attach adapter which extends the dovetail bar providing a platform to fit the zwo EAF in two...

These are parts for mounting two NEMA17 drives on 10" Skywatcher dobsonian telescope.

A versatile Newtonian reflector telescope boasting a sturdy Dobsonian base, drawing inspiration from the iconic Orion XT8 model.

In 2018, I received an 8-inch Dobsonian Telescope from SkyScrapers Inc., courtesy of the Amateur Astronomical Society of Rhode Island at the Frank Evans Seagrave Memorial Observatory in North Scituate, Rhode Island. The model depicted here is not to...

This thing is a 3D printed Dobsonian telescope designed for an 8" primary mirror with a focal length of 48". The optical tube assembly consists of aluminum extrusions attached with 3D printed ribs designed for standard hardware and covered with...

Altitude bearings for small Dobsonian telescopes consist of mounting holes to screw onto wooden cradles for optical tubes. The bearing diameter is 150mm; width is 25mm. Light sanding of bearing surfaces may be necessary to remove print artifacts. The...

This is another design for the altitude bearing of a Dobsonian telescope, an improvement over my previous design: https://www.thingiverse.com/thing:2637742 The lever arm of this design is twice as long (6" vs 3") making the balance of the scope less...

This is a reflector telescope and stand I designed that uses mostly 3d-printed parts and the rest is very easy to find. Advantages of this design is the hight of the eyepiece, it allows you to stand up straight when looking at the stars so its more...

A 16" Dobsonian telescope 3D model boasts intricate detailing and authentic textures, crafted in Blender using the Cycles rendering engine. ...Customizable color options are available, while the model is specifically optimized for Cycles-powered...

I've continued my previous telescope project, constructing a 12-inch (300mm) Dobsonian truss scope with a shorter focal length of about f6 compared to the initial 10-inch f9.8 version. The modular design allows for easy adjustments in mirror cell and...

Drop-in replacement for eyepiece racks that Orion used to bundle with all of their XT-series dobsonian telescopes. They still feature pre-drilled holes in the mount for the rack, but no rack is included in the accessories package. ... This eyepiece...

This printable telescope features a collapsible optical tube assembly that collapses into a compact cakebox form protecting the optics, and a sturdy dobsonian mount that can be set up and ready for stargazing in under 5 minutes. The optical tube...

Using a 2-inch eyepiece is perfect for observing celestial objects with the Newtonian Sky Watcher telescope.

I managed to procure a 12-inch (300mm) mirror boasting a focal length of approximately f6, significantly compacting the overall telescope size, thereby rendering it noticeably easier to manipulate and employ as compared to the prior 10-inch f9.8...

To accurately position a laser beam as a finder on my telescope, I need assistance with assembly. Kindly follow the provided images and secure all components firmly. Fasten the laser to the fine adjustment screws using a rubber band. ...Employ...

Sky-Watcher 120ED Telescope with Celestron Equatorial Mount Tripod is a high-quality, photo-realistic model that boosts detail and realism to any of your rendering projects. The model boasts a fully textured, detailed design that allows for close-up...

bearings two - 625z 5mm*16mm three - 608z 8mm*22mm 3 rings carved from furniture chipboard 16мм thick. OD=380mm. ID=325mm. ... Ramps 1.4 3d printer pcb + ESP8266 wifi OnStep firmware Project...

Ideal for 10mm eyepieces as well as 4mm eyepieces, this is truly exceptional.