sky hero spy 3d models

... Activated! ...Get Sky-Hero Spy into Action Now! ... **Emergency Mission Briefing** Rotate 3D Printing Guidelines by 90 Degrees Utilize Ultra-Thin Layer Height: 0.1 mm Infill Settings Adjusted to 40% Material Specifications: High-Temperature ABS

A mounting plate that fits the hole pattern on the sky hero spy, allows wires to be run underneath. Can be used on upper and lower plates. ... Instructions Mount with M3 bolts and lock nuts.

This is a GPS mast mount for the Sky Hero Spy multicopter. It also fits other multicopters with 30mm tubular arms, such as the Sky Hero spyder and trooper models. The mount was primarily designed for use with the folding GPS mount available from...

Mounting a Dragon Link 433Mhz dipole antenna is extremely easy on your Sky Hero Spy Y6 hexacopter, you'll require an additional M4 screw identical to those that secure the arms.

When building a Sky Hero Spy frame, this clip comes in handy for an M3 screw placement between the frame sections. Rotate and print these instructions at 90 degrees, ensuring optimal clarity. ...Opt for ABS material and low layer heights of 0.1 to...

A printed isolator block which holds 2 M4 bus bolts for power distribution. Instructions You will need... 2 Hexagon Head M4 x 20mm bolts. 2 M4 half nuts 2 M4 lock nuts Slot the M4 bolts into the...

A mount to fix a DJI Zenmuse H3-2D or H3-3D gimbal to A Sky-Hero Spy. The Mount also acts as a canopy latch for the front canopy. This mount is in 2 parts, a plate that attaches to the bottom frame plate via 2 of the standard mounting holes and one...

Brace for Power - Secure Attachment Clip for Enhanced Explorer or Top Gun Soldier by SkyHero or RCTimer

... bulb is specifically designed for mounting directly onto the motor-mount of a high-performance Spy or Spyder 6 vehicle. ...It's also perfectly suited for installation on the compact pancake-style engine housing found in the elite Sky-Hero model series.

It's suitable for use on pancake versions from Sky-Hero. Print Settings: Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: No Resolution: 0.1, 0.15, or 0.2 mm Infill: 15% Notes: Place the flat side of the bulb on your bed for better...

This is a straightforward installation procedure for the Naza GPS Puck specifically designed for the Sky Hero Spy drone.\n\nGet started by printing this assembly with high-quality ABS material, employing a reliable 0.2 mm layer height.\nSecurely...

The Sky Spy from the Marvel comics looked quite a bit different from the Marvel TV series. I printed this using my Elegoo Mars for most of the parts, but the dish was made on my Ender 3. Some sanding may be required. ...Two main bodies are included in...

... the Sky Spy Satellite on top of mainframe in Teletraan 1 mode. ...It hooks onto the port Sky Spy stores on to prop Sky Spy on top of Teletraan 1. I printed with a brim and on its back. ...Depending on your printer you may or may not need the brim.

... Transformers Cartoon. ...The little Sky Spy satellite that Teletraan 1 sent out to scan vehicles and would later feed the Autobots information throughout the series. ...It might look better if it was resin printed, but I had this translucent gold PLA+.

The Sky Hero Spyder Canopy is a must-have accessory for your RC Quadcopter, providing protection to its components while adding style and durability to your aircraft. This canopy is designed specifically for the RC quadcopter, ensuring a perfect fit...

Anakin Sky Hero from www.rcgroups.com/forums/showthread.php?2455099-Sky-Hero-Anakin-build-discussion/page94 Measurements EDIT: Body.stl is a One-Part Jib

Simple modification to integrate a discovery buzzer from HobbyKing into a Sky-Hero Anakin. ...Secure the buzzer firmly in place using two cable ties, attaching it directly to one of the carbon fiber boom arms on the Anakin.

... the copter stable by preventing it from sliding or skidding around on the ground. Designed specifically for the Sky Hero Spyder, these ninjaflex-printed spacers are a game-changer for pilots who demand a responsive and controlled flight experience.

Simple design to integrate a discovery buzzer from HobbyKing into a Sky-Hero Anakin. Secure the buzzer in one of the carbon boom arms using two cable ties. ... Printer Settings: - Printer: Felix 3.0 - Rafts: Disabled - Supports: Disabled - Resolution:...

Three distinct arm designs for Sky-Hero Anakin are being created, allowing him to utilize each position effectively. Printing these arms in PLA was a preferred choice due to its rigidity. ...While it may be more prone to breaking, the material is...

I designed three distinct arm variations for Sky-Hero Anakin, allowing him to utilize each position seamlessly. ...To achieve maximum rigidity, I opted to print them using PLA, a material that may be brittle but is inexpensive to replace when damaged.

Humans beware of this cunning spy who excels at deception, capable of ambushing from behind and concealing his true identity within the ranks. He masters the art of stealth, able to blend seamlessly into his surroundings, becoming nearly invisible in...

This is a custom esc tray designed to accommodate 2 ESCs DYS SN40A within the arm of a Sky Hero Spider multicopter. I created this tray primarily for effortless esc mounting on X8 layouts of the Sky Hero Spyder. ...The cover clips have distinct designs...

Little Spyder Alt-Sky Hero Alternate, known for its remarkable speed and agility on both indoor and outdoor tracks, stands out due to its remarkably shorter leg span compared to standard models, making it ideal for young children or casual users.

This is a set of precision-engineered frame spacers designed specifically for the Sky Hero Little Spyder. With these spacers, you can now carry larger and thicker Lipo batteries in the battery compartment. ...A range of spacer options is available,...

This is an escape tray designed to shield one ESC, Dynamics Systems SN40A, within the arm of a Skymax Hero Spyder quadcopter. ...The protective covers exhibit subtle differences in their attachment mechanisms, with distinct configurations for the upper...

Both trays are available in 30mm, which is the original sky hero size, but also in 31mm and 32mm, allowing you to enlarge the lip of the battery slot and carry thicker batteries. You can use your original screws. ...(self-tightening M3 screws) I suggest...

I have created a custom-designed 3D printed component that serves as a mounting solution for integrating two LED boards and a Spektrum Satellite receiver into the Sky-Hero Anakin drone.

I planned to outfit my Sky Hero Little Spyder with Cobra 2204 1960kV motors, but the stock motor mount doesn't accommodate these compact motors since they weren't designed for this quad copter. This modification is not endorsed by Sky Hero; proceed...