skr pro 3d models

Since the original Fan cover doesn't fit, I created a new one. Printed it with a **0.5** nozzle and variable layer height (0.2-0.32). It can be printed **without support**. I put just a little in the entrance. ...Since the underside is not...

Split up into smaller chunks so it could be printed on my 180x180mm secondary printer. Assembly: - Insert brass stand offs from existing electronics mount into Body 1 and Body (Insert carefully with a hot soldering iron to ensure these parts are...

M3x20 screws and M3 nuts

This is pretty much useless but uploading it so others don't go the same dead end :) I had a 60mm fan lying around so thought I will remix the original cooling tunnel for it. However, the design does not work. All of the air seems to be reflected...

DIN Support for BTT SKR Pro 1.2 With 120 or 140 fan.

This is a front case for a BigTreeTech SKR Pro 1.2 for an Ender 3 Pro. ... Additional required materials: 8 M3x8 screws 2 M3x10 screws

V3 mount has been tested and working on the SKR PRO V1.1 ================== -------------------------------- Ribbon Cable Breakout PCB Board Beefed up trace width where possible. Heater PCB trace has trace on both Front and Back. Heater connector...

https://github.com/SkullKill/cr-10s-pro-mods/tree/master/RibbonCable_MB_BreakdownBoard Modified Marlin source code has been made to accommodate the Stock CR-10S Pro LCD/TFT touchscreen Display:...

This adapter enables seamless integration of the new SKR Pro V1.1 board with either an MKS Gen L V1.0 or SKR V1.3 mount, allowing users to harness the full potential of their 3D printer setup. The adapter has not yet been printed for testing...

An Ender 3/3 Pro BIGTREETECH SKR PRO V1.2 case With neodymium magnet lock mechanismus Two parts - a case and a lid Material needed: - 5x2mm neodymium magnets - 4x brass M3 inserts ( https://www.aliexpress.com/item/32850041010.html )

so all mount points are M3 threaded.hardware used1 X bigtreetech SKR PRO V1.1 board4 X 2209 Drivers1 X Ribbon Cable Breakout Board with I2C EEPROM (AT24C256)1 X 40X40X20mm fan, 40X40X10mm fan should also work.4 X M3 Stock Screws (used to hold the...

SKR Pro BTT EXP-MOT Mount plate goes in first sliding into the Z axis mount under the printer. Then the VGA brake out mount goes on top of it. SKR Pro mount does have a place to screw in the step-down board for a capacitive probe. I would not...

SKR Pro BTT EXP-MOT Mount plate goes in first sliding into the Z axis mount under the printer. Then the VGA brake out mount goes on top of it. SKR Pro mount does have a place to screw in the step-down board for a capacitive probe. I would not...

The new SKR PRO version is untested as I do not own one, and all measurements were taken from a reduced mesh of the PRO board model available on BigTree's site. Note that: * admodesi's Driver Duct will need to be slightly modified to clear the...

This is a set of mounting plates that will allow you to mount an SKR Pro 1.1 board or an MKS SGen board into a Creality control box for a CR10 or CR10S

Hardware Used: Bigtreetech SKR PRO V1.1 board Four 2208 drivers, soon to be upgraded to 2209 UART Ribbon Cable Breakout Board EEPROM (AT24C256) Three M3 stock screws for attaching the mount to the chassis Four M3 10mm screws for holding the SKR and...

"endstops and 5160 drivers.7z" I installed 4 TMC5160 v1.2 stepper drivers onto my BigTreeTech SKR Pro v1.2. I didn't cut any pins or solder anything, just plugged them in and slapped the heatsinks on. You have to hook up an external power supply...

Control box for the SKR pro 1.2 board and the tft35 touch screen set. Front/Rear cover plates are optional, the grille is used in front of the fans. Supports needed on long openings, print the top with the rear of the top on the build plate.

Full diff: Changes to the right (SKR Pro) case: - 5 mm higher rails (z) - allows install without removing Y-motor. - +10 mm taller (z) - (allows for 15mm fan installed inside case, with stepper driver heatsinks) - 20x10mm cutout at bottom for LCD...

Moving it higher allows it to clear the board.I still need to assemble everything.This is a remix of the nicely designed "SKR PRO case remix" by vandenmar: https://www.thingiverse.com/thing:4870495Which was based on the "SKR PRo V1.2 + TFT35 E3...

Moving it higher allows it to clear the board.I still need to assemble everything.This is a remix of the nicely designed "SKR PRO case remix" by vandenmar: https://www.thingiverse.com/thing:4870495Which was based on the "SKR PRo V1.2 + TFT35 E3...

----- This is a remix of the nicely designed "SKR PRO case remix" by vandenmar: https://www.thingiverse.com/thing:4870495 Which was based on the "SKR PRo V1.2 + TFT35 E3 screen mounting box for MPCNC" by Bobbond000:...

This is Marlin 2.0.1 optimized for the Anycubic Kossel Linear Plus printer, paired with a SKR PRo 1.1+TFT 35 LCD and TMC2209 V3.0.Linear Advanced disabled by default. You'll need to fine-tune the PID settings to achieve optimal performance. I've...

An elegant fan duct design for cooling your stepper drivers on the BTT SKR Pro v1.2. The duct just snaps right onto the fan and then the fan is bolted onto the mount which is attached via standoffs to the board. Parts: Provided heatsinks...

Designed an adaptor plate for the SKR Pro 1.1/1.2 from BigTreeTech, to fit in a Ender 5 Plus. It's designed to dissipate the heat off of the stepper drivers by utilising a 40mm fan on the side. It also mounts a Raspberry Pi on the Top for use with...

This is a remix of [SKR Pro v1.2 and TFT35 E3 v3.0 Case by gamble604 December 07, 2020](https://www.thingiverse.com/thing:4678675). Partial quote from original thing: > Three-part case for the SKR Pro v1.2 with a TFT35 screen used to run a Primo...

... I upgraded to an SKR Pro v1.1 and needed additional space, so I decided to add more features while still keeping mounts for an SKR V1.3 or V1.4. It utilizes the power supply lid as a top panel and positions the fan directly onto the driver chips.

This design accommodates mounts for the BTT SKR Pro, two MOSFET boards, and a 120mm fan, with power from your supply routed through any of the numerous hexagon holes to suit your specific needs. The hexagon holes also serve as useful locations for...

A convenient add-on allows you to easily attach the circuit board, eliminating the need for the standard inserts that come with it.