skeleton 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

As of 09/16/2018, I've not yet modeled or printed the capstan bearings, nor have I fully solved how I will drive the capstan. My current thought is to use a drill attached to the underside of the platform, using a belt to drive the capstan. I would...

I recommend 3 loops since this is quite a small model. Otherwise not enough PETG is dumped before the start of the parts</p><p>Print bed recommendation: Powder coated steel sheet with glue stick. I usually just put a 5cm to 10cm light line on the...

(Not required for revision 2) Scaling: The model as is in the STLs will accommodate most types of earbuds, however it can be scaled down as much as 30-35% for smaller sets. If you use earbuds with an inline control, such as the ones shown in the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

It can print without support, and if you have the workflow dialed in, it takes only about 30min per label from start to finish. You might get away with printing just the modell without the support stuff…. didn't try. Depending on your bridging it...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_pattern_thickness = .8 custom_back_extra_port_y_size = 30 custom_back_camera_corner_resolution = 8 custom_top_port_x_position = -10...

Unfortunately, do not have access to a Prusa printer all the time, so testing will take a little while ----&nbsp;Let's make this work together!;Because I can only test 1 day every 1 or 2 weeks on a Prusa printer, you can help me design this knob and...

Taller models have a tendency to cool in the middle and pull the bottom up at the corners. If your workspace/office is 75 degrees and you printer is not in an exclosure you should probably use some kind of adhesive. I found Glass+Glue worked for me...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

This model will do the same stuttering if printed too fast even with the used a reduced segment count (50) in the cylinders. The trusty SD card worked for me with a big batch of these. The other solution was to slow the print down.Let me know in...

In addition, in case you want to remix you would potentially only have to adapt the holder model.The bottom of the holder has a cavity that exactly fits a specific lightning cable found on Amazon with angled connectors to reduce the space it...

It will not fit a full sized stepper, use their model if you have the original stepper motor. I suggest printing with the end that hooks over the carriage on the bed with supports on bed only. There are minimal supports this way and the hook keeps...

Safety Information Please be aware that this product contains small items and is not suitable for young children.This product is a scale model and is intended for use by adults and children age 14+.Take care during use as some products may...

useful as an object holder (Elettronics component, Dyn, various tools, modellism, cutting and sewing, make-up set, manicure, fishing ... etc https://youtu.be/w3FsHNZxC64 Description The chest of drawers is made up of five containers with single...

I always use a 4-5mm brim around such big models. You may need to turn off the skirt line then.</p><p>The 8 holders inside were printed with 100% infill, just to be sure that they were stable enough. You will need some screws, washers and nuts as...

These models come with an unsupported and presupported version. This Bundle contains the following: Dr. Balthazar Morris Gideon Morris Gravewalkers Gravehounds Medical Carriage(Free in the welcome package for Patrons!) DnD Datasheets DnD...

If you look at the print of the base (or the model of the legs) you will see there is a round hole with three slots surrounding it. These slots fit a specialized washer that is used in the vise to keep the base from rotating when it has been...

First, I modeled the front of the display to fit the RepRap Discount Full Graphics Smart Controller. Then, I also decided it needed a back to protect the circuit board. Easy peasy! Next, I tackled the problem of mounting a TFT35 touch screen...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

Fits Both "Research" and "Research Plus" Models. Don't Lose Precious Time with Clips or Carousels! Print *Your* Holder **Now** ;-) # Materials Required - 4mm Aluminum Rod (2x 18cm Minimum) - 2x M5 20mm Screw With Hex Head - 2x M5 Butterfly Nut -...

You can find the newer version here: Phone Mount for Van Moof S2/S3 V2.0====================================================================&nbsp;Rotating Phone Mount for the Van Moof S2/S3 electric bike.Mounts to the handlebar using 3 cable-ties,...

It started with a Bachmann starter set with a steam loco and a couple of cars (Durango & Silverton in case my other models didn't give it away). This came with a bunch of EZ-track. I had full intention of expanding my layout so I bought more...

Since my first published keybboard was The1987 (https://www.printables.com/model/299777-the1987-a-modular-retro-inspired-87-key-mechanical) and it's fairly popular, and its designed around the Phantom circuit board and Teensy 2.0, which are no longer...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

These two parts are rather small but also simple ball joint parts that rely on friction and cannot be tightened. For those of you that want a to be able to tightly secure your camera in a certain position, there are also parts that form a double-ball...

The straps used to complete the clamp are downloadable from the original model's site https://www.prusaprinters.org/prints/122320-one-for-all-cable-strap-print-in-place-clamp How to create your clamp & accessoriesSelect the clamp size relevant to the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

This model is cheaper than the usb c version and charges the Oculus Quest perfectly. This greatly improves your playing time and you could even charge the battery while using it. One design came close to what I liked, but was made for a different...