six and mono 3d models

Hello there, this is a support to let you to drain your resin bottle in to the VAT. It could be used with plate installed or not, and also with different size of resin. I think is very useful and in different situations. Print Settings Printer:...

this is a remix of another design rotated 180 degree and made to sit on the right side. angled to drip into resin vat. ... resized for a easier fit.

Drip for the Anycubic PM SQ printer. ... 4 mm wall thickness. 3 layers of wall when printed. 0.6 mm nozi and 0.28mm layer height Ender3 V2 printed, 2 hours 15 minutes

Leila Rosano. ...Solo Female Representation of Asia. Board Game Development Project 2017. Power and Femininity Through the Figure of the Witch. ...For More Information, Visit https://catedracaceresuna.wordpress.com/leila-rosano-2017/.

... This model showcases a retractable landing gear system and a steerable tail wheel for added maneuverability. ... If anyone prints out this plane, please share your results along with your thoughts on how it can be improved upon in the future.

Take an old support piece with a flat bottom and stick it in one of the corners flat side down. 3. Print this file. 4. Remove the print once complete by pulling up on the support pieces. 5. Go back to printing whatever you want! The STL, LYS...

Take an old support piece with a flat bottom and stick it in one of the corners flat side down. 3. Print this file. 4. Remove the print once complete by pulling up on the support pieces. 5. Go back to printing whatever you want! The STL, LYS scene,...

It now has 10mm fillets on all of the corners and the lid cutout is angled 10 degrees to sit level when in use + .1mm larger so the lid will slide in a bit easier and not rub at all. Tolerances are tight so make sure your printer / filament...

... vat.Two versions are available, the full version is ment to be printed flat on larger than MK3 build plates. ...The second version is cut in half and printed on edge to fit onto the MK3.Created starting from: https://www.thingiverse.com/thing:4646943

    The printer magnet overall is sturdy and not flimsy at all, i'm pleased with the outcome and this was a fun project!The Base, Lid and Nameplate can print directly on build plate, the Z axis will need some supports.   I had so many...

... a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. ... It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the back-center. ... A M3-.50 nut is required.

https://www.thingiverse.com/thing:4765628) A simple but effective way to prevent those few drops from reaching just outside the vat when you put something on the dripping holder and to shove the build plate and the dripping rack back onto the arm. ...

https://www.thingiverse.com/thing:4765628) A simple but effective way to prevent those few drops from reaching just outside the vat when you put something on the dripping holder and to shove the build plate and the dripping rack back onto the arm. I...

In the photo, I used 6mm bungee cord cut to 150mm (6 inches), marked with a pen and bent at 115mm (4.5 inches), plus 25-30mm of 0.2 wire for the crimp, and then covered the ends with shrink wrap to tidy them up. ... If you make a spreader: use 10 or...

Click the link to get notified.Assembly documentation can be found here: https://outofmarbles.com/pages/docsThis lifting mechanism is the first stage of the bigger marble machine and I had to test it thoroughly before I put it into a bigger...

This is good for small failures where you might have something stuck to your FEP. Instructions: Remove the bed plate. Take an old support piece with a flat bottom and stick it in one of the corners flat side down. Print this file. Remove the print...

The 3D model is crafted on a real car foundation, ensuring accurate dimensions, meticulous quality control, and unparalleled likeness to the original. Model formats available: *.max (3ds Max 2008 scanline) *.max (3ds Max 2008 vray) *.fbx (Multi...

... effectively for me. The design falls under GPL with a no-commercial clause due to being a remix. Kudos to pentaglut and b2x! ...Printing vertically without support delivers good results, but consider printing flat with support for optimal outcomes.

... Table Lamp Icon, Target Icon, Tire Icon, Trolley Icon, TV Icon, Umbrella Icon, Wall Icon, Wireless Icon. Not enough for you? Ask for it! Feel free to ask me anything about my models and designs by "E-Mail" on my profile page or "Skype: ZahMeTR".

... In the original model the build plate was 220mm wide (typo when designing?). The other parts - MonoX_Build_Plate_Mount.stl and MonoX_Build_Plate_to_Gantry.stl - are taken directly from the original, but included here to keep them as a set.

... In the original model the build plate was 220mm wide (typo when designing?). The other parts - MonoX_Build_Plate_Mount.stl and MonoX_Build_Plate_to_Gantry.stl - are taken directly from the original, but included here to keep them as a set.

I'm designing a toy for my little one, and it's all about spinning things around. He loves watching objects whirl by, so I created something special just for him. Firstly, the wings aren't perfectly symmetrical, which means they need to be printed...

Also use higher infill because taking material in those places will make hanger weaker from original design, so test it strength after printing and maybe print it with 30 degrees rotation to assure higher layer adhesion, but this totally depends on...

As I designed and printed a drip bracket before, I realized its shortcomings. Most if not all brackets is tilted in one direction only. I found that is not good enough, so I tilted this one in two axis. I also moved the center point, but could...

Degreased the lower part of the platform and glued the magnetic base. Liked the idea with a magnetic base, for easy removal. But since I was not sure what would hold out with a large print area, I decided to first try on a homemade plastic one. I...

As I designed and printed a drip bracket before, I realized its shortcomings. Most if not all brackets is tilted in one direction only. I found that is not good enough, so I tilted this one in two axis. I also moved the center point, but could...

Airbrushing and General Painting Solutions

Modeling, sculpting, and texturing: Amandine Delmarre Developed by Tarsier Studios and published by Bandai Namco Entertainment.

Bring on that cold one and let's drink up!

A standard dice with rounded edges and engraved holes