singing microphone and stand 3d models

Small stand for tonor mic, original one was to tall for my needs.edit: Added additional bolt and nut to print ;]

I designed a replacement tripod for my BM800 microphone because the old one had been holding together with nothing but tape. I decided to give it a complete makeover in order to participate in the competition. If you find my designs helpful, consider...

It is an easy modular stand.

... I have designed and printed many things around the house, and find FreeCad very easy to use. This was designed for a 1/4" Carriage bolt with a finger nut to help hold it in place although it clips on my Mic stand fairly sturdy so I may not use one.

this was a mike stand that I use for the Razer seiren the big adapter is the one that fits under the mic and the side screws are the same as the ones that it comes with. ...the size of the big hole is 16mm and the two side ones are 6mm

A cap attached to the stand is slightly conical and features self-threading capabilities, allowing for easy assembly. To combine the parts effectively, you will need two 3- or 4-mm screws, which fit snugly into the smaller holes also equipped with...

A handheld mic with a sturdy stand crafted entirely within Blender's software confines.

My DIY wireless mic stand checks out with flying colors after a thorough inspection by our quality control expert, Cat!

Print Settings: Printer Brand: RepRap Printer: Prusa i3 MK2 Rafts: No Supports: No Resolution: 0.2mm Infill: 40% Notes: Printed from PET, a great choice for this application due to its strength and durability. ...Carbon fiber could also be used as an...

Modular Microphone Stand Logitech Rally Mic Pod Logitech Rally Mic Pod Modular Microphone Table Stand

customize the size for your certain mic stand, Here are my settings in cura Slicer X - 27 Y - 37.8523 Z - 12.0761

Very simple Mic Stand for Audio Technica AT2020. ... I have the XLR version, should be fine for USB too - plz check the inner diameter.

I attached the scad file. Printed from PET because good strength is needed. Infill about 40% 0.2 mm layer height Just print 4 identical parts, reuse the metal bits and replace the original bakelite parts. Print instructionsCategory: Music Print...

I wanted a more substantial stand than some of the others that I was able to find, so I created this adjustable height desktop stand to fulfill that need. IMPORTANT: Make sure to change your printer slicer setting to inclusive of this part will...

Attach this rapid prototype hook to a mic stand or any 15mm tube via its clip-on design. Use your RepRapPro Huxly printer for PLA printing. ...Afterward, utilize the hook for hanging items on it.

This is an adapter you can use to help replace the stock condenser-mic on a MicroKorg keyboard. ...It has standard 5/8"-28 threads for mic-stand stuff so you can put a gooseneck or whatever on it.

This is a simple little adapter that I designed so I could mount my digital wifi microscope on my boom mic stand. ...It has a 3/8-16 thread which I had to clean up with a tap after printing.

This is a base for a Rode DS1 desktop mic stand. ...The standard round metal foundation gives way under the weight of a heavy mic like the NT2-A.

The supplied tripod sits too high for my needs, so I designed this stand. It should fit anything that takes a 5/8" threaded mount. ... I printed it on a Prusa Mk2.5s with a layer height of 0.2 but with adaptive layering enabled to get the finer...

......I ordered this little clamp from Amazon: https://www.amazon.com/gp/product/B09L88CFBYThe top piece snapped off after only a few months of usage. Designed a replacement part for it that could reuse the extra-long clamp that came with the Amazon stand.

Grip (cone-shaped): Depth: 14.4mm Smaller diameter: 24.1mm Bigger diameter: 25.5mm Stand's height from the base to the grip's axis: 73.25mm The base is on a plane of a circle with a diameter of 100mm

Requires 1 x M5x25mm bolt and nut.M5 nut need to be inserted during printing of Knob v2.stl after layer 28 (0.2 resolution).

I crafted this design to overcome the standard maximum height limitation that didn't meet my needs. ... To achieve the desired outcome, I utilized a 20% infill, eschewing both raft and support features during the printing process.

... my Zoom H1 still towers over my workspace, making it difficult to position it comfortably on my desk. ...To solve this issue, I use this adapter, which allows me to lower it down and keep it out of sight, giving me a clear view of all my monitors.

<p>Even on my smallest tripod, my Zoom H1 is a bit too tall to keep on my desk. ...This keeps it a little lower, so I can push it back, and it doesn't block the view of my monitors. Category: Gadgets

You will need one M5x25mm bolt and one nut. The M5 nut needs to be inserted during the printing of Knob v2.stl after layer 28, which has a resolution of 0.2. ... To support my work, please consider buying me a coffee at ko-fi.com/L3L42LH7Z.

HOLDER OF THE MICROPHONE STAND

Microphone with mechanic stand :D

Four legs microphone stand/mount

... and visual effects. It's not typically associated with designing radios or microphones. If you meant to say that an old radio and microphone were designed using Blender, the sentence would be: Old Radio and Microphone Designed Using Blender