singing microphone and stand 3d models

This is a phone stand styled after the vintage microphones of the 1940s

Microphone stand with UNC 3/8"-16 thread. ...First, print the threaded part to test compatible with your microphone before printing the other parts. Category: Music

Powerful microphone stands are equipped with sturdy clips that securely hold both upper and lower components in place. ...The lower clip features a spacious compartment designed to accommodate the audio cable connecting your tablet, ensuring a stable...

A straightforward, DIY-friendly microphone stand cable clip designed specifically for use with FreeCAD. Easily customize the design to suit your needs and preferences. ...For added sturdiness, print the component as a solid object.

These are some pieces to make your own microphone stand. ...You only need to print the 4 pieces, 2 rods of 12mm diameter, 2 screws with nut and a clamp.

... thread that Mic clips demand, so I decided to share it with the community in case someone else needs one. The custom-built stand measures 130mm from base to mic clip and is more than robust enough to securely hold my heavy Rhode microphone.

This interface piece bridges the gap between the mic stand and the microphone suspension - a design seen in Rodé's setup. At one end, it features a 3/8-16 UNF thread that fits standard microphone stands perfectly. ...A M6x15mm bolt is used to tighten...

## Backstory This stand was designed to replace the standard shockmount included with many Aliexpress BM-800 clones and similar microphones. The original mini tripod stand was too small in all dimensions, making it impractical to use. It was too...

... stand is crafted from simple PLA. Required Components: You will need an M5 screw and bolt to assemble this stand. ... Included Files: The necessary Gcode files are provided, as well as STL and Solidworks models for easy modification or printing.

So i ended up making this 3D model because i needed a microphone stand quickly. So here is my design, it use the 5/8-27 standard thread used on many microphones. Approx 15cm in height and 12cm base diameter. UPDATE: I added a 60 degrees angle...

I need a sturdy adapter that will securely fasten a compact telescope onto a versatile microphone stand.

Base stand for rode microphone VideoMicro. No supports required. Additional Hardware: - m3 screw - m3 nut for locking mechanism. ...

The Samson C01U microphone comes equipped with a simple stand that demands minimal setup. To get started, simply submerge the upper bracket in warm water and carefully bend it inward, allowing the detents to function as intended. ...With this...

This is the stand for our microphone that is used for AI applications, 2 pieces for the ease of printing and to increase robustness. ...The body piece can stand in place without any glue or you may still use a fast action glue to attach the body part to...

This was a custom-designed stand for my Razer Seiren microphone, built to fit the unique adapter that attaches directly under the mic's body. The screws used on this stand match those provided with the Seiren itself, ensuring a seamless integration.

Humans use a microphone stand with a parabolic reflector, positioning their voice at the focal point within the curve. By directing the parabola towards your mouth, you can comfortably place the stand anywhere from 1.5 to 3 feet away. ...This eliminates...

This is a microphone stand extender for Sony UAB-80. you can extend height about 15cm. Maybe this model is compatible with the general mic stand. ...

The base is slightly larger and perhaps better looking.Print SettingsPrinter Brand:UltimakerPrinter: Ultimaker OriginalRafts:NoSupports: NoPost-PrintingPrint the foot, screw the microphone stand adapter that hopefully came with your microphone on it,...

A bit of parts salvaged from : - Stand : https://www.thingiverse.com/thing:1993382 (has some nice plugins for the stand if you're into that kind of thing) - SM57 microphone holder : https://www.thingiverse.com/thing:2091162 On the Double holder, the...

A microphone stand I made for my elgato wave 3 microphone. I wanted something shorter and out of the way. I used a .4 tip with standard quality on my CR6, but I bet a .6 tip would do fine. I made the inserts to the base a snug fit so it doesn't...

Backstory This is a stand for the standard shockmount included with many Aliexpress BM-800 clones and other similar microphones. The included mini tripod stand was just too small in all dimensions. It was too short which meant that the microphone...

It's fairly basic, but is designed to minimise the space taken up on the desk and to reduce the overall height compared with the supplied stand so that the microphone does not obscure your monitor screen. The overall height, including the...

A sleek microphone stand that embodies minimalism. This iteration shares the exact same interface as its predecessor, a design available on Thingiverse with the reference number 1425977. ...Its base has been enlarged and polished to perfection, giving...

Simple stand for a SingStar mic that fits any conical microphone with a shaft diameter of at least 32mm at its thickest end. ...Designed in Fusion360 and scaled down by a factor of 1000, although I didn't bother fixing the error.

Customizable for any microphone by adjusting the top and bottom diameters to match the taper of your microphone at a precise 4mm separation. Mine is a Shure 10A with an outer diameter of 37mm at the top of the mic. This utilizes the "arc" module in...

Adjustable phone holder for microphone stands When you cant remember your lyrics when playing guitar, clip this in front of your face and just read the lyrics over the microphone while still playing guitar. You will need an elastic to make it...

Genius Lapel Microphone Support

I bought a joby microphone but not a stand. ...Should work with the quarter inch bolt provided by the manufacturer (I think about 3/4" in length?).

This is a simple stand designed for cardioid condenser microphones. Print it upside down with supports! I hope folks find this useful! ...

This is the oft-faulty small plastic component of a microphone stand securing mechanism to link the stand components together. In case you're experiencing this issue, here's the solution. I printed it in PLA with 0.2 layer height, 0.4 nozzle size,...