sindoh dp200 3d models

I created one of the emoji decorations I entered into the Sindoh Decoration Contest in 2018. This model will take approximately 45 minutes to print and measures about 3 inches by 3 inches. The ring is 10mm in diameter externally and 2mm thick. Thanks...

This ornament was one of the designs I created for the Sindoh Decoration Contest in 2018. It will take approximately 45 minutes to print and measures about 3in x 3in in size. The ring itself has a diameter of 10mm (on the outside) and is 2mm thick. ...I...

I'm entering this innovative solution into the Sindoh Design Challenge for spare parts for vehicles. This essential cover was created to address a pressing issue: when riding a unicycle, riders are frequently struck by rocks that shoot up from the...

... I utilized Sindoh Flexible filament so it could be flexed around the end to hold in place and be abrasion resistant. PLA or ABS would likely break during installation due to their rigidity. ... I highly recommend printing with support structures.

I created one of the emoji ornaments I designed for the Sindoh Decoration Contest in 2018. It takes around 45 minutes to print and measures about 3in x 3in. The ring has a diameter of 10mm on the outside and is 2mm thick. I appreciate you taking a...

This ornament was created specifically for the Sindoh Decoration Contest of 2018. It will take approximately 45 minutes to print and measures about 3 inches square. The ring itself has an outside diameter of 10mm and a thickness of 2mm. I appreciate...

I'm showing off one of my emoji ornaments from the Sindoh Decoration Contest of 2018. It'll take about 45 minutes to print and measures 3in x 3in. The ring has an outside diameter of 10mm and a thickness of 2mm. Take a look around, thanks for...

This ornament was one of my designs for the Sindoh Decoration Contest back in 2018. With a print time of about 45 minutes, it measures roughly 3in x 3in in size. The ring has an outer diameter of 10mm and stands at 2mm thick. I appreciate you taking...

This ornament was one of the designs I created for the Sindoh Decoration Contest back in 2018. It takes roughly 45 minutes to print and measures about 3 inches by 3 inches. The ring itself has a diameter of 10mm on the outside and stands at an...

... to be working well so far. It was printed using my Sindoh printer, which came with 1/2" ball bearings and a single 608 bearing. ...Since I'm still new to this process, I strongly recommend inspecting the print thoroughly before deciding to use it.

... type. ...M3 screws could also be viable. The top part must be printed right side up with support and backside print, ensuring the flat side is downwards; it was successfully printed on a Sindoh 3DWOX 3D printer using Sainsmart Black ABS filament.

... rate of 15%. To see how to tie this camelHanger in action, check out the video: https://youtu.be/dDrwJ3wZRQ8. Print Settings: Printer: Sindoh RICO; Rafts: Yes; Supports: Doesn't Matter; Resolution: Normal; Infill: 15%. ...Post-Printing Instructions:

... settings chosen. Here are the specifics: Print Settings: Printer: Sindoh Rico Rafts: Not necessary Supports: Not required Resolution: Normal Infill: 10% or more Note: The clock's surface appearance will vary depending on the rafts option selected.

My entry for the Sindoh Smart Assistant Competition boasts four slots designed specifically for pens or pencils, three dedicated SD card holder slots, a compact bin perfect for storing an average-sized wallet, a designated coin receptacle for those...

I printed it on my Zortrax M200 and Sindoh 3DWOX, using both PLA and ABS with the recommended settings from the slicer program. It turned out great. I also made one with 50% infill; it feels more rigid and steady. The support is a bit challenging to...

... doesn't look like one but still is a Christmas tree - it's a plot twist! Merry Xmas, hohoho! This object was created using Tinkercad. https://www.tinkercad.com/things/0l2DLvuTd1q #TinkerChristmas @MyMiniFactory @tinkercad @Gearbest @3dwox_sindoh

... or you could drill holes in the sliders to attach them. This might not be perfect, and you might need to make some adjustments. It's a start. Hope you can use it. I'm printing with a Sindoh 3DWOX with the standard print settings using PLA. ...

I'm excited to share with you one of my emoji ornaments designed specifically for the Sindoh Decoration Contest back in 2018. This particular design should take around 45 minutes to print and measures approximately 3 inches by 3 inches. The ring...

I'm showcasing one of the custom emoji ornaments I created for the Sindoh Decoration Contest in 2018. This design takes approximately 45 minutes to print and measures about 3 inches square. The ring itself is 10mm in diameter on the outside and a...

I'm showcasing one of the emoji ornaments I came up with for the Sindoh Decoration Contest back in 2018. It should take roughly 45 minutes to print and comes out about 3in x 3in in size. The ring itself measures 10mm in diameter on the outside and is...

This is one of the awesome emoji ornaments I created for the Sindoh Decoration Contest back in 2018. It'll take around 45 minutes to print and measures about 3 inches square. The ring itself has a diameter of 10mm on the outside and is a sturdy 2mm...

This is my entry for the Sindoh #3DPIMPMYRIDE automotive parts competition. As you can see from the description, I've created a 2" (52mm) gauge pod. I've been using this 3D printed gauge pod in my 1998 Subaru WRX for several years now and it's never...

Now, let's take a look at the print settings used for this project: Printer: Sindoh Rico Rafts: Not necessary Supports: Yes, they are required Resolution: Normal quality is sufficient Infill: I chose an infill of 15% or more to achieve the desired...

This is my entry for the contest #FIXMYHOME sponsored by @sindoh. I redesigned a simple plastic component that's incredibly easy to misplace. It's a partition wall for the liquid soap reservoir in the DREAN washing machine, so check out the images to...

This is one of the custom emoji decorations I created for the Sindoh Decoration Contest back in 2018. You can expect printing time to be around 45 minutes, and its dimensions are approximately 3in x 3in. The ring itself measures 10mm in diameter...

... and more refined. To create an even more visually appealing design, I deliberately tilted the clock back by five degrees. Print Settings: Printer: Sindoh Rico Rafts: Not Applicable Supports: Not Necessary Resolution: Normal Infill: 10% or More

I printed this at 60mm/sec on my Sindoh 3Dwox instead of the suggested 40mm/sec default and did not see any adverse effects. ...The slight layer shifting is more noticeable in photos than in real life, but my bed screws were a little loose, which...

... a layered transparent board with black tiles sandwiched between them (vector files are included). This set was specially created by Robbert Bakker from the Netherlands for the Board Games Spare Parts Challenge hosted by Sindoh on MyMiniFactory.

I'm submitting my entry for the Sindoh smart assistant device 3D printing competition. It's a custom Echo Dot desk holder that lets you attach your choice of side panels, giving you complete flexibility in meeting your specific needs. The design also...

Print Settings: Printer: Sindoh 3Dwox Rafts: Ignore This Setting Entirely Supports: Pay No Attention to These Options Either Resolution: Fine-Tune the Layer Height to Exactly 0.2mm Infill: Opt for a Solid 20% Fill Density Notes Nozzle and Extrusion...