simplisafe doorbell wedge 3d models

A case made for the basic Wyze doorbell and an 20° horizontal and 5° vertical wedge to mount it.

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

Mount a Ring Pro adapter that adjusts the camera's viewing angle. ...I incorporated a substantial wall plate into this design, which conveniently concealed a gaping hole in my home's stucco exterior.

This is a spacer for the Aqra G4 to make the camera look more towards the floor.

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

... Since the wedge is quite thick, I made it so that the wedge screws onto the wall, and then the Ring Video Doorbell screws onto the wedge. ...That way you can still use the original Ring screws to attach your Video Doorbell onto the wedge.

Buddy randomly uses a blink doorbell to spy on his printer so I added a wedge mount for his doorbell onto the tool holder (not sure who to attribute the tool holder to because he just sent me the STL). ...Works great.

User cmar had engineered a wedge mount for the Ring Doorbell. ...I adjusted its position slightly, shaved off some excess material, and carefully carved out an arch on both the top and bottom to facilitate effortless detachment from the print bed.

Cheers to creator Bootjevaarder from Prusa Printables original design which I remixed to fit the smaller chassis of the Eufy Video Doorbell 2E (Battery). The screw holes (on center) are about 12mm closer together in this remix and the wedge is about...

I customized @themuli's Ring Pro doorbell wedge for my unique needs by adding a 10-degree downward tilt, relocating the screw holes for easier installation, and incorporating ribs to fortify the screw holes. Please note that unlike the original...

50° inclined support for Netatmo doorbell. 50° bracket for Netatmo Doorbell. ... ( 45° also available on request, and any angle less than 50)

50° inclined support for Netatmo doorbell. 50° bracket for Netatmo Doorbell. ... ( 45° also available on request, and any angle less than 50)

Wedge mount with angle increased to 35 degrees.

I created a custom mount for my Ring 2 doorbell that fits over the trim/molding on my door. I'm not sure if this molding is standard, so you should check the dimensions before printing it yourself. This mount can be installed on either side of the...

... setup with the Corner Kit. ...Use the Corner Kit to angle your Video Doorbell Wired towards your walkway, so you can improve your motion detection and get a better view of visitors coming to your door. Designed by Thom Benjamin - CO SmarThuis

The metal mounting plate of the PoE version is a little bit different so I made the following edits: - Made the inside hole bigger - Opened up the holes for the security screw Not the most beautiful edit but it does the job and it is not visible when...

A 20-degree angle provides optimal mounting for the Ring Video Doorbell Pro, allowing the camera and motion sensor to capture more footage than when mounted straight on. ...Its sleek design features mirrored symmetry, making it versatile enough for use...

This was a really awesome way to customize a wedge. Big shout to Zapta! The thingiverse customizer was down so I used SCAD. I never used it before and I totally geeked in my pants. I edited this a little in tinkercad. I didn't want to have to turn...

This was a really awesome way to customize a wedge. Big shout to Zapta! The thingiverse customizer was down so I used SCAD. I never used it before and I totally geeked in my pants. I edited this a little in tinkercad. I didn't want to have to...

I found it helps to print the bracket at a roughly "good enough" angle and then make a bunch of small wedges (that is, the bottom of the bracket) in 2.5-5 degree increments. The wedges can be glued to the bracket to play with the angles without...

Customized version of https://www.thingiverse.com/thing:2754727 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2754727