simplisafe doorbell mount 3d models

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

Needed for siding. The angle is 8.75°. Sits proud about 0.7 inches at top and 0.125 at bottom. ...Use with existing back plate and long screws included.

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

I split the original piece into two sections and created a divider that slots neatly into position between them, matching my exterior trim perfectly.

I carefully attached my Ring device to the thin molding surrounding my entranceway.

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

Customized version of https://www.thingiverse.com/thing:2003791 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003791

A simple spacer to allow a doorbell to receive a 4mm surface mounted cable. ...Useful for adding additional controls to garage door openers.

I was drawn to the Ring Pro mount by drdobsg, but it departed from industry standards in its mounting hole locations. Since I had already installed our doorbell using the standard wedges that came with the Ring Pro, I sought to reuse those holes. I...

... my doorbell circuit. ...This solution provides a mounting bracket for a Unifi G4 doorbell with room behind it to splice the connection, and an enclosure above to house the reader. ... Details at https://lo.calho.st/posts/homeassistant-keycards/

... the design of Nostack and wanted it to fit the Ring video doorbell wired. ... so i adjusted the size and mount holes to the right size of this Ring doorbell. ... credits to Nostack / Remixed from design: https://www.thingiverse.com/thing:3992038/makes

... design of Nostack and wanted it to fit the Ring video doorbell wired. ... so i adjusted the size and mount holes to the right size of this Ring doorbell. ... credits to Nostack / Remixed from design: https://www.thingiverse.com/thing:3992038/makes

Buddy randomly uses a blink doorbell to spy on his printer so I added a wedge mount for his doorbell onto the tool holder (not sure who to attribute the tool holder to because he just sent me the STL). ...Works great.

Eufy Video Doorbell Mount for New 2K Battery/Wired Unit:\r\n\r\n1. Replaces existing standard doorbell and uses same screw holes.\r\n2. Features custom threaded screw hole covers.\r\n3. Includes channels to run wires to the back of Eufy mounting...

Inspired by https://www.thingiverse.com/thing:4752704This peephole mount is designed for Eufy 1080p Battery Powered Doorbell (C210)https://www.amazon.com/dp/B08DXD8LSRFitting peephole larger than 14.5mm

This is a replacement part and upgrade for the eufy 2E Battery Doorbell (2K) mounting bracket that uses a 16 lb command strip instead of screws like the mount that comes with the doorbell. This is useful for those who live in apartments, rental...

I created a custom mount for my Ring 2 doorbell that fits over the trim/molding on my door. I'm not sure if this molding is standard, so you should check the dimensions before printing it yourself. This mount can be installed on either side of the...

A 20-degree angle provides optimal mounting for the Ring Video Doorbell Pro, allowing the camera and motion sensor to capture more footage than when mounted straight on. ...Its sleek design features mirrored symmetry, making it versatile enough for use...

This design is tailored for a wired Eufy video doorbell, boasting recessed mounting holes that fit seamlessly into standard rectangular doorbell templates, and matching in height to ensure a precise fit. A convenient pass-through hole allows for...

User cmar had engineered a wedge mount for the Ring Doorbell. ...I adjusted its position slightly, shaved off some excess material, and carefully carved out an arch on both the top and bottom to facilitate effortless detachment from the print bed.

... use the attached f3d file. For assembly, put M3x12 screws into the mounting plate of the doorbell, put the camera onto the mounting plate and install it onto the printed part. ...You won't be able to remove the camera without loosening the screws.

This angled stand elevates the SimpliSafe indoor camera to capture an optimal view from above, tilted at a precise 14.8-degree pitch. ...The accompanying foot securely fits into a dedicated slot, ensuring a snug and stable connection.

Ring Pro doorbell camera 45 degree mount I wasn't able to find a mount for my Ring Pro doorbell camera that put it at an angle like I needed. Also added a hood to the mount to reduce rain from beading up on the lens and to minimize sun glare. I...