simplisafe doorbell angle mount 3d models

The new Simplisafe doorbell requires an angled mount to function properly at my house, so I created one. A few aspects aren't quite right, but it works and is secure. The mount was designed to position the camera for wall mounting perpendicular to...

I designed a custom doorbell mount for my Simplisafe system, which extends the device out from the doorframe, allowing it to be perfectly parallel with the street. This clever solution eliminates the awkward angle that previously had the doorbell...

Spacer for Mounting Simplisafe Doorbell Camera: Overcoming Brick Wall Blindspots To eliminate blind spots caused by brick walls, my previous doorbell's location on the frame was relocated to sit flush with the wall or shutters using a spacer. To...

This is a mount for battery powered video doorbell that is angled to allow use on a wall perpendicular to the door. ... Countersunk holes for mounting the plate were drilled after printing, and the camera mount was screwed directly to the plate after...

***Major Update 11/18/2019*** As of November 2019, Two Different Mounting Brackets Exist for Simplisafe Video Doorbell Pro. My SimpliSafe Video Doorbell Pro has mounting holes spaced 77~78mm apart for attaching a bracket to my wedge. Newer models...

An Angled mount for the Blink Camera. I used it to mount my camera just figured id upload it. ...Material: Platemp:200cspeed:45m/swalls:6 layersInfill:35% infill.Supports: nonAdhesion: Brim

Mount was created to fasten doorbell backplate to mount using #6 screws and hex nuts. Update - Added an updated version which puts the mount slightly to the side in the case of brick being next to the door frame. I also added a cut away tab along the...

The SimpliSafe doorbell is vulnerable to theft by an experienced thief within approximately 15 seconds without any modifications. This upgrade significantly increases the difficulty of stealing, making it more challenging for a potential thief to...

Ring Doorbell Elite Angle Mount

I've also renamed the design from "Nest Doorbell (Battery) Mount - 35 degrees" to "Nest Doorbell (Battery) Angle Mount" 08/27/21 Designed a 35 degree mount for the new Google Nest Doorbell (Battery). All the dimensions and design elements are taken...

If you need a slight angle for the Eken V7 doorbell you can use this. Doesn't matter how you place it you can use it on the left or right side. ... Just make sure you got long enough screws.

I created Ring Doorbell Mount (wired version) specific to my entrance which at 45 degreee angle with the brick wall.

45 degree angle mount for wired Ring doorbell. Some support is needed for printing this. I'm happy for any enhancements of this design. ...

This is an angled mount for the Ring Doorbell 2. It's angled 10 degrees down and 20 degrees to the left. If you want it to the right than you can mirror it in your slicer. ...Also the 2 mounting holes for the house were for my specific application,...

... software. The two mounting holes provided were tailored to accommodate my particular installation requirements, which featured a standard rectangular doorbell button. ...To ensure proper alignment, these holes are carefully spaced at 53mm apart.

Case and 45 degree angle mount wedge for EKEN doorbell camera. Provides a solid pressure fit that prevents easy camera removal. ...Angle mount allows you to let camera look down a hallway or see people approaching the door to the side.

A customizable corner/tilt wedge angle mount for the Amazon Blink Doorbell. STL files for various turn & tilt angles are attached, and others can be created by customizing the attached SCAD file. Note that both turn & tilt can be enabled...

This is an angled mount for the Ring Doorbell 2. It's angled 10 degrees down and 20 degrees to the left. If you want it to the right than you can mirror it in your slicer. ...Also the 2 mounting holes for the house were for my specific application,...

The case consists of two parts: the main body that securely holds the Dropcam device and has space for a USB cable, and an insert that keeps the camera firmly in place when mounted. To accommodate the wire running down the door frame and into the...

... slots on the back, allowing for seamless integration with the camera's mounting system. The added benefit of a slight downward angle ensures optimal viewing coverage, while the large central hole provides effortless wall mounting capabilities.

This is a mount for a Simplisafe indoor camera to go into a corner of a wall. ... It uses original hardware from mount that comes with camera

Supports "Everywhere" to Mount Keyboards Securely This Design is Specifically for the SimpliSafe Keypad (circa Dec. 2019) The Original Keypad Mount from SimpliSafe Was Known for Being Flimsy, and It Didn't Allow for a Normal Grabber Screw Due to...

This is a wall mount for the SimpliSafe Control Panel. This is a tight fit (on purpose) and needs trimming to open it up very slightly, and doesn't need a bottom hook for that reason. ...The supportive sides and the firm fit make it very secure.

Designed this mount to secure my fob next to my bed and nightstand as a simple way to arm/disarm my simplisafe along with keeping the panic button at the top for easy access in case of an emergency. ...I would suggest printing it vertically since its...

This is a wall mount for the SimpliSafe Control Panel, that I created after seeing that the manufacturer did not offer it. Created from scratch in Tinkercad after seeing another model online. This is a tight fit (on purpose) and needs trimming to...

This is a drop-in adapter for the SimpliSafe SimpliCam, allowing you to mount your cameras on the wall, rather than on a shelf with the original stand. It has a built in wire pass through if you choose to run your wire up to the ceiling for better...

This is a remix I made of the wall mount for the Simplisafe base station. I wanted to separate the parts so I didn't have one long build but instead 3 shorter ones. I also adjusted some of the dimensions a little. After printing I used super glue to...

This is a wall mount for the SimpliSafe Control Panel, that I created after seeing that the manufacturer did not offer it. Created from scratch in Tinkercad after seeing another model online.</p> <p>This is a tight fit (on purpose) and needs trimming...

This is a remix from a wall mount on Thingiverse by spiceyux. I wanted to separate the parts into three pieces for shorted print times. I also changed the dimensions a little and added a lip for the bottom. ...After printing I used super glue to hold...

Mounting bracket for replacement door sensor magnet used in SimpliSafe home security systems.