simplify3d snapmaker 2

Left and Right side Roller mounts for setting up a custom rotating engraving system for the SnapMaker 2.0 Once parts are assembled and attached to the printer you need to loosen the bolts on the rails and press down slightly on the printed brackets...

Hi all, as the Snapmaker 2.0 PSU is known to be quite noisy I was looking for ways to quiet it down a bit. Since most of the existing mods require either modification of the original back plate or need a whole new printed backplate I was thinking of...

This is in regards to a forum thread for Snapmaker 2 https://forum.snapmaker.com/t/3dp-part-cooling-fan-5015-replacement/10038/93 It's time to unveil my contribution to the blower mod upgrade! Starting with Brent's printed mod, the blower itself,...

To connect the 1 1/4 inch vertical fixed port (FixedPort1_25ext.stl) to the snapmaker 2.0 CNC spindle head, remove the M2 screws and replace with 3 M2-0.4 x 8mm flat head screws. [M2-0.4 x...

This is my version of the Snapmaker 2.0 power supply bracket. I saw that there are many on here and other sites that try to hide this power supply (and its Turbine sounding fan). I didn't have the enclosure so and I didn't want to poke holes in my...

This is my version of the Snapmaker 2.0 power supply bracket. I saw that there are many on here and other sites that try to hide this power supply (and its Turbine sounding fan). I didn't have the enclosure so and I didn't want to poke holes in my...

Snapmaker 2.0 has no fixed Zero Point for machining For alignment I created a very simple 160x160 90° angle which is fixed by up to 7x M4x14 Screws in the worktop nuts, used for CNC-carving. You can leave screw-holes unattended to use the nuts in...

The Snapmaker 2 magnetic print sheet is prone to be dislocated in case the nozzle gets caught on some warped or overextruded part of the print. This causes layer shifts and failed prints. Remixed from brackets designed to hold a glass plate in...

This is my version of the Snapmaker 2.0 power supply bracket. I saw that there are many on here and other sites that try to hide this power supply (and its Turbine sounding fan). I didn't have the enclosure so and I didn't want to poke holes in my...

Fan holder & duct for snapmaker 2.0 original 3D print head. <i>not tested on the upgraded 3D print head with cooling slits in front!</i> It clamps into the side slits and holds it tightly. Additionally I've added provisions for cable routing (see...

This is my version of the Snapmaker 2.0 power supply bracket. I saw that there are many on here and other sites that try to hide this power supply (and its Turbine sounding fan). I didn't have the enclosure so and I didn't want to poke holes in my...

https://forum.snapmaker.com/t/a250-mod-with-linear-rail/28513 The Step file is just the complete mock up of the snapmaker A250. Note not exactly to the mm done. just a sketch for myself to test some ideas. but if someone like it. please feel free...

# Adapters for linear guides for the Snapmaker 2.0 To reduce the wobbling of the build plate I have installed linear guides that provide additional support. These adapters help to connect the guides to the buildplate. Especially when doing cnc...

This is a complete alternate cooling solution for the Snapmaker 2.0 power supply. Notes* 1. I had to remove the lighting inside the power supply including the diffuser and the circuit board that controls the breathing effect (personally I wanted...

This is a fix for the Snapmaker Dual Extruder Module. The clip that hold the gear assembly into place is weak and often unclips, resulting in failed prints. ...This piece fits within the opening on the clip to prevent it from unlatching.

If you have the Snapmaker A250/A350 and the matching enclosure... well .. then you know that the filament is catching on the left column as the extruder is moving from the home position down. This nifty little mod makes sure the filament is guided...

Inspired by Kelvin8r's design, remodelled in Fusion360 to adapt latest Snapmaker Artisan which has a 9mm spool shaft. Using 608 bearings. Designed to fit over a 56mm inner diameter spool. ... Updated: V2 with a thinner plate and offset outer plate...

This concept is based on a similar design though is compatible with the rubber stoppers provided by SnapMaker for holding work items in place during laser engraving. Unfortunately, it's limited by the laser bed's groove spacing. While each of the...

I wanted to attach standard 4" exhaust ducting to my Snapmaker A350 enclosure so I could use inline duct ventilation fans to exhaust my laser fumes more effectively. This adapter allows a direct connection, and uses the existing holes and screws...

See [my post in the forum](https://forum.snapmaker.com/t/3dp-part-cooling-fan-5015-replacement/10038/267?u=nivekmai) where I was diagnosing this, make sure your slicer is spitting out the correct gcode before printing, or you're probably going to end...

... Internal recirculating air filtration unit coming soon! Check out my ongoing Snapmaker Forums post on the other mods I have on my machine here: https://forum.snapmaker.com/t/cnc-bracing-for-added-rigidity-other-mods/29444?u=elliot

Adapters to connect the Snapmaker bed frame to the linear rail guide supports. This upgrade adds supports at the front and back corners of the bed frame to prevent bending down during actions at the limits of the vertical axis Version 4 will...

This is for a 3.8mm high bed that is just slightly (0.5mm) larger than the Snapmaker bed in all dimensions. Make sure to only adjust inner walls and not outer walls, as adjusting outer walls may cause them to run in to the Z axis rails. ... One...

Customized with snapmaker writing, and added some additional cut-outs to reduce filament usage. I use this with a tube slid inside ( i bought this as it comes with the correct pipe and end fittings:...

Print Settings Printer: Snapmaker A350 Rafts: No Supports: No Resolution: .2mm Infill: 20 Filament: MatterHackers PETG Translucent Green Notes: Designed to be printed with a .4mm nozzle printing specifically at .2mm (or less) layer height, there are...

Print Settings Printer: Snapmaker A350 Rafts: No Supports: No Resolution: .2mm Infill: 20 Filament: MatterHackers PETG Translucent Green Notes: Designed to be printed with a .4mm nozzle printing specifically at .2mm (or less) layer height, there are...

After assembling the Snapmaker Enclosure, I realized that the tri-fold doors needed a better way to pull open the doors when they are shut. Came up with this simple door pull that fits the bill and doesn't get in the way of the doors when they fold....

Tested spool brands include: * Snapmaker 1kg * Esun respool 1kg * PrimaValue 1kg To assemble the spool holder, you'll need to acquire: * Ball bearing 608 2Z 8x22x7 mm (available at https://www.remlagret.se/products/608-2z-skf-8x22x7-kullager) *...

I have had my Snapmaker A250 for about a year and a half now and LOVE it - it meets all my needs in a multi-function machine, yet the handheld touchscreen has always been a bit of a hassle IMHO. I didn't like the limited options for placement, the...

I've uploaded each table below as a Snapmaker Luban project so you can adjust sizes or make any changes you want. The 3 tables are as follows: *Interval - This is just 15 comparisons with the only difference being the fill interval being...