silhouette couple 3d models

Add more value until you are comfortable with the tension required.Servo can be placed in couple different ways, to the top or to the side as in pictures shown.Now to the aligning of the metal arm on the servo. When you move the servo back and forth...

(update: after much comparison, the alternate horn definitely works better!) For another experiment, I super glued two of the larger inner cone diameter rotors together and aligned their slots properly with a couple pieces of filament while the glue...

Instead, the count took her as his lover.This made the countess furious at Arastacia and the countess had a bitter rivalry from that very moment.A couple of years went by, where Arastacia lived in the guest quarters of the castle, but she still...

If you've managed to figure out how to 3D print in general, then you should have no trouble assembling this thing after looking at a couple pictures. Alt-Azimuth Adjustable Base can be found here: https://www.thingiverse.com/thing:5411792 ...

You will need to put together the following Sub assemblies:2  x  BackLeg_SA2  x  FrontLeg_SA2  x  TopLink_SA2  x  BottomLink_SA5  x  CrossSupport_SAThe 3D printed components, with or without nut...

the point of the thread) on either side. Then, update the Expression value in the ConnectDiameter row (the box highlighted yellow below) with this found value.Connector Length -            Measure the height (in MM)...

I’ve also a couple of ports (antenna and micro USB) that I also wanted to exclude the fuzzy effect from around.Since PrusaSlicer allows for any shape of modifier to be used, in CAD I selected the area I wanted to be fuzzy and extruded them two...

It is much sturdier than a couple of lightweight lack tables stacked vertically so I don't need the bottom table as a stand. The legs of the table are connected to the shelf with a steel plate on top for fire safety. I really don't like the idea of...

  If you cannot get the wire installed, STOP and investigate the print, since it should not take a great amount of force to install the wires, and you may have an issue with the print which is blocking the holes for the wire hinge.  Do not push too...

Keep using those ties or a couple of small M4 bolts that can be tapped using your fingers into the Prusament Spool, see appropriate holes in the photograph attached..If you suspend the spool from a tree or other object then a large plastic tie (or...

It mechanically couples a spinning gyroscope (thru some gearing) to a pair of feet that stomp up and down. When one foot goes down, the body actually lifts up and then starts to precess clockwise. Then when the other foot comes down the body lifts...

Theres not a lot of room in the gun so this fit may take a couple tries. Wiring the gun is the only tricky part. With the trigger in the front half of the gun it’s advisable to the use a small connector between the trigger and FCU so you can take...

I tried to print a couple of different versions of this style of puzzle, but I had no luck… One puzzle fell apart while trying to solve it, while the others fused parts together. Despite attempts to adjust my flow rate and scale the model, I was...

I have a Gotek drive and CF-IDE card reader for my Amiga 4000.As I already use the 5,25” bay for a CD-ROM drive, and one of the 3,5” bay’s for the original Floppy drive, I needed another solution.My A4000 has a standard height floppy drive, so there...

=========================================================== __Update: May 9, 2021__ A quick update on our progress and a couple more pictures. You can see the two Dyna-Soar nose cones next to each other. As the original nose on the left needed to be...

Also you can see a couple extensions and the water reservoir that makes life easierThere are many possible combination and maybe you end up with something like thisOr like this, maybe that.Upgrades.April 10 - Wall support added to the...

You can follow these instructions if you don't know how to : https://www.google.com/amp/s/www.wikihow.com/Open-a-Combination-Lock%3famp=1Keep the numbers of the combination somewhere as it will never change. Glue the 2 pivots to the door...

Wait a couple of days, verify the leveling and adjust the position.I upgraded my MK3S+ to MMU2S adding extra weight on the already heaviest part of the printer. I use 6 balls and may add an extra one.</p><h3>Print instructions</h3><p>PETG is supposed...

There're a couple things you can configure before flashing your Arduino: rf24_rx[5] - Is a 5-character channel that is the unique id for each puck, for individual addressing. Give each puck a unique number but leave the first three characters...

Also, the solvent is basically set after a couple of seconds, but the joint is still soft. I normally wait 24 hours before I use glued parts to ensure that the plastic softened by the solvent has hardened.</p> <p>6/6/20<br/> Added new version of L1...

There are a couple of things you'll need: A thick wire that serves as a 'skeleton' of the model holding all parts together and in place. I used the core copper wire of a coaxial cable with a diameter of around 1mm. very thin enameled copper wire to...

Probably a good idea to print a couple of the mounts. It's easy to screw it up when adding the brass inserts. You'll want a piece of PTFE tubing between your extruder and the radiator. Measure the depth of your radiator, and the depth of your...

You may want to take out the filter and give it a shake every couple of months to reduce filtrant clumping; not sure whether it makes a difference but can't hurt. The design is now in my "nice" category; readily available parts, minimum of print...

The Y-Splitter snaps nicely in place on the back cover of the printer.Remove the stock coupling. </strong><i>I wanted to reduce the weight and length of the whole setup. Since this model has pneumatic connectors on all 3 entries, the stock one isn't...

You will have couple of second to realign, depending on the speed of your superglue. 4. Without removing the pressure on either of the blind nuts, spray superglue accelerant on both locations; the superglue should take hold instantaneously. This is...

This way the filament can simply be cut during the ‘Release Filament’ procedure, eliminating the need to disconnect, then re-attaching the ptfe tube at the extruder.  Parts Needed:  Download and print one of each: EasyCut  and curved PTFE30R90...

The list of parts you will need is as follows:An Arduino-based microcontroller (Arduino Pro Micro in my case)A real-time clock module (DS3231 or similar)A TowerPro MG995 continuous rotation servo motorA standard LEDA standard light-dependent resistor...

city a couple of millennia ago. Despite her previous failures and trusting her instincts, she poured her will into creating a portal in that direction. She was pleasantly surprised when the entrance opened in the destination she desired. "Oh,...

The receiver coil should be over the non-perforated region of the base. WIRELESS POWER:The major change here is that I added an wireless receiver module to the bottom of the assembly coupled with a wireless transmitter module for installation under...

You will need to flip the parts yourself after bringing the 3MF into your slicer.&nbsp;Using the ironing feature creates a nice flat finish, which drastically reduces the amount of sanding required (or you can leave it as-is).&nbsp;I find using 0.3...