sigma 35mm lens 3d models

In this photograph, you can see a high-quality test print showcasing the standard .8 pitch slip-on lens gear attached to the Sigma 35mm f1.4 lens. ...The included STL model provides an accurate replica of this useful accessory, featuring a toothed gear...

Standard .8 pitch slip-on lens gear for the Sigma 35mm f1.4 lens. Tested on Canon mount, non-cine version. ID is 75mm, should fit any lens with same focus ring dimensions. ...Photo is a test print, included STL has a gear that spans full width of focus...

This is a small mod that can be screwed to the back of the Sigma 18-35mm f/1.8 lens that makes the image appear like that of an anamorphic lens, mainly by elongating the bokeh. ...This effect can be seen pretty clearly in this video by "We Are Film",...

I combined two designs, one for the lens mount and another for the hood. It's highly recommended to use supports when assembling this project. ...Special thanks go out to Lumanation and Dabinielson for their contributions!

Tested on my K-mount example of this lens that uses an 82mm filter thread. ... Extra inner bayonet mount allows the hood to be locked onto the lens for storage Mine printed without supports, your mileage may vary.

A new take on the original for compatibility with the Sigma lens. Simply print and utilize it! ...:)

Simply rotate the ring to effortlessly remove the lens cover, eliminating the need to physically take it off. ...To install this innovative replacement, print the file "Blende 2x" twice and refer to the provided photo for precise assembly instructions.

You can view this item on Thingiverse here: https://www.thingiverse.com/apps/customizer/run?thing_id=9860 Using these settings: mount_base - is set to 3 buckle_width - is now 42 buckle_gap - is currently at 15 lens_diameter - is a diameter of 62...

Pentax 35mm Lens Cap

This lens hood was tested in yongnuo and canon 35mm f2 lens

Bayonet-style lens cap designed to fit Sigma lenses featuring an 82mm filter size, compatible with the 18-35mm f/3.5-4.5 model and other similar lenses.

The Sigma 15mm F/2.8 Fisheye lens cap requires a 100% scale print using ABS material. ...Successful prints have been achieved with two shells and 10% fill.

The Sigma 20mm 1.8 Lens Performs Nicely \n A Little Versatile/Lean When Printed with ABS Plastic - But Fitted Securely And Works Effortlessly!!!

Designed specifically for the Sigma 18-35mm f/1.8 lens, this product is based on the LH780-06. It will likely fit any Sigma lens that meets these criteria: -> Has a minimum focal length of 18mm -> Features a 72mm filter thread To reflect heat and...

Folow focus ring for sigma 18-35mm. ...Hardstops is measured for automatic FF motor calibration.

This is a lens cap for an old Sigma 24-200mm lens, it's a bit odd as it required a bayonet fit rather than a compression one. ... Print Settings Printer: CTC 3D Printer Rafts: ...

I remixed the Sigma 50-100 f1.8 Lens Hood by Mr_3D in Tinkercad and added Petals to the end of the hood. Thanks to Mr_3D for doing all the hard work. ...I had to drop the print .2-.3 mm below the build plate on my printer as it was a touch to thick on...

A very simple yet useful lens cap for the Sigma 17-70mm lens.It screws onto the end of your lens tigthly enough to stay in place, but not too much that it becomes difficult to move.Im not sure if it fits other lenses, but if you try, let me know in...

The Lens Lock is a collar that securely fits around the exposed shaft of the Sigma 150-500mm lens when extended to its full 500mm focal length. This camera lens is incredibly impressive, but unfortunately, it cannot be locked into place at a specific...

A small lens cover to mount filters on a small 35mm camera

Here is a custom lens protector designed for 35mm lenses that doubles as a sun visor. I've included the SolidWorks file if you'd like to make any modifications. To print this design exactly as shown in the image, simply rotate it 90 degrees (adjust...

This is a storage/transport box for a UW-Nikkor 35mm Lens (Nikonos 35mm Lens)This project has two files.The Box The LidThe Lid with TextThey are supposed to be held together with (6mmx10mm) magnets. You will need 8 of them. The fit is quite tight so...

I grasped a caliper firmly in one hand, carefully examining the worn-out Leica Elmarit 35mm lens hood I had rescued from my collection of photography gear. With a sense of determination, I set out to design a cap that would protect this valuable...

By working on a project that necessitated a camera lens, I repurposed old film camera components to craft an adapter ring suitable for Minolta 35mm lenses. This DIY accessory may require certain hardware from a camera, but an affordable option can be...

Lens hood for the Sigma Art 18-35mm f/1.8 lens. Prints easily and without supports in about 3 hours, uses less than 40g of material. ...I used PET-G but PLA would work too, though it might deform and loosen under stress after some time.

To adapt GoPro footage for a 35mm film, follow these instructions: first, set your GoPro's resolution to 1080p and frame rate to 24fps for cinematic look. Then, import the footage into editing software and apply a 2.39:1 aspect ratio to match 35mm's...

This is a Prototype of my Hardstop Focus Ring for the Sigma 18-35mm Art Lens. First test works good but the inner diameter was a little bit to small. ...I fixed it and clean the whole side of gears that isn´t in use - our Printers will say Thank you ^^...

Sigma SD rear lens cap proves elusive on the web, prompting necessity for Sigma users with access to 3D printing technology.

A Customizable Lens Shade for Sigma's 18-250 Zoom Lens Printed to Perfection with a 0.3 Millimeter Layer Height.