sidewinder x1 v4 3d models

If your Artillery Sidewinder X1 V4 printer was bought after July 2020, please use this updated version as the others are impossible to install correctly without increasing the stress that is already placed on the cable. ... **WILL NEED 4 SMALL SIZED...

Artillery Sidewinder X1 V4 Extruder Ribbon Cable Support Version 3 is a lightweight design that minimizes moving mass. It relies on factory bolts and one zip tie for secure attachment. When paired with an additional rainbow ribbon cable, this support...

Artillery Sidewinder X1 v4 Z Axis Adjustable Belt Tensioner This is my take on a basic z belt tensioner. I built it by remixing two other well-known tensioners from Thingiverse and incorporating some of my own design ideas. The mounting bracket...

The stock arm measured 0.5cm below and 0.8cm off-center for my Sidewinder X1 V4. Perhaps a newer version has an altered mounting point or manufacturing variations are at play. My AC bed cable features a thick sheath instead of the mesh design found...

Cable strain relief for the heated bed cable on the Artillery Sidewinder X1 v4 printers, remixed from coDesign's https://www.thingiverse.com/thing:4458289 which didn't fit mine. This is suitable for late 2020 V4 printers, where the bed cable is...

###Beefed AC Bed cord support for Artillery Sidewinder X1 v4 I tried another design but it was flimsy. So I hacked this together from the beefed up version of the original:**https://www.thingiverse.com/thing:4458289** by **coDesign**. The cable...

This is a cover for the SD and USB connectors on top of the Artillery/Evnovo Sidewinder X1 V4 3D printer. It's inspired by the model from Danimod (https://www.thingiverse.com/thing:3834321). I wanted to not only cover the space between the connectors...

Another important note, I used the incredibly detailed Sidewinder X1 model by Rick and Morty from grabcad (https://grabcad.com/library/artillery-sidewinder-x1-1). Unfortunately I found, that the X1 v4 is slightly different from the v1 model. The...

This is my Cura 4.7 profile for PLA, using an Artillery Sidewinder X1 printer. Printing speed is a bit low but you can speed it up if you want. ...Let me know if you have any issues with this profile.

Edit: New version that has a cable relief for all versions of the Sidewinder X1: https://www.thingiverse.com/thing:4775480 This is a cable strain relief for newer X1's (I got mine mid Oct. 2020). I wanted one that could just slide on without...

... edge of the cable. ...Please see photo. If yours is the same then this will fit. Two cable ties and your good to go. Print Settings Printer: X1-V4 Rafts: No Supports: No Resolution: .2 Infill: 25% Filament: Generic PETG Black Category: 3D Printing

Cura 4.13 PETG profile for Artillery Sidewinder.

In order to upgrade firmware on the main board of your Artillery Sidewinder x1 printer, you have to disassemble the base of the printer, disconnect the TFT controller's power cable, then tip your printer back over and load the firmware. Once done,...

I looked around and couldn't find a good support for the X ribbon cable on the gantry for the Sidewinder X1. This one is pretty simple, you can either mount it to a T-nut or you can print off the one with an integrated T-slot adapter and just put a...

It's possible that Artillery made changes to the latest version (X1 V4), which I purchased in January 2020. To fix this issue, I designed a new idler with more material at its weak points and improved stability on the stepper axis. I also created...

In order to upgrade firmware on the main board of your Artillery Sidewinder x1 printer, you have to disassemble the base of the printer, disconnect the TFT controller's power cable, then tip your printer back over and load the firmware. Once done,...

... same! ... This one was re-drawn to fit the V4 with the dimension of 57mm give or take a millimetre from the edge of the glass to the edge of the cable. Please see photo. If yours is the same then this will fit. Two cable ties and your good to go. ...

T00LF00L's Human Handle Originally Created on Thingiverse as Part #4051910, Later Modified with Raised Text for Enhanced Visual Appeal, Featuring 200mm Spacing Between Holes for Added Customization.

A version for assembly with commercially available M3 screws and a second version for assembly with threads from Ruthex.

Since a little metal chip was blocking the original part from fitting, I shortened it. ...The tolerances are really tight, so beware.

... X1 (V4) will allow you to obtain a good ventilation during your prints! ... Hardware needed: - Artillery Sidewinder X1 (V4) 3D printer - Bondtech BMG - E3D Lite 6 HotEnd - M3x5 screw (x2) - M3x16 screw (x2) - Washer for M3 screw (x2) - M3 nut (x2)

... ...The bed part didn't line up with the cable. It was about 27mm to far to the right. I have created a different angled version to fit the bed and cable position. This is for an Artillery Sidewinder X1 V4 US 110 Volt model bought in January 2021.

This a 4-in-1 upgrade of the Artillery Sidewinder X1 V4 with BMG Wind/Aero clone extruder, 5015 fan, BL/3D Touch auto leveling (using the Waggster mod) and BL Touch firmware to improve printing quality. This is a remix of previous mounts by making...

Forgive my damp filament. ... Simple quick print, no supports needed.

My Cura 4.7 profile for PETG. The stl file I uploaded could be used as a test, it should be printed with cooling activated. For larger models, deactivate cooling. I'm using a .4 noozle. ...Let me know if it works or if I should improve it.

I made caps to cover the threaded rods that protrude at the top of the gantry to avoid accidents with the protruding metal rods

This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/9dhEx7zDoxb This is a Remix of IroncladComp's CR-10s Pro Wyze Cam (Mount.https://www.thingiverse.com/thing:4552118) FEEL FREE TO OFFER ANY ADVICE OR OPINIONS! ... I...

I designed this cap for the x-axis profile of the printer. Let me know if you like it! ...For the first layer use a slow print speed since the logo is tiny.

Remixing the SW X1 V4 Strain Relief by Hans9K, I've rounded and thickened key areas for added robustness and widened the neck of the strain relief to perfectly align with the larger cable bundle found on the V4.

On newest Sidewinder X1 (late 2020) the bed cable is positioned towards the center of the bed. So i had to modify the bed cable relief. It has the great design from coDesign which avoids leverage on the bed springs. You'll have to disassemble...