sidewinder x1 v4 3d models

this is modified version of cable support to fit for the new version of Sidewinder X1 V4

Filamentführung für Artillerie Sidewinder X1 V4

Here is and adaptor for de Artillery Sidewinder X1 V4 (2020)

Another squashball feet for Sidewinder X1 V4.1 with 2 parts feets. Only need M4 8mm screws and nuts. ... Screw it directly before like I did.

Another squashball feet for Sidewinder X1 V4.1 with 2 parts feets. Only need M4 8mm screws and nuts. Screw it directly before like I did. ...

Spool roll holder for artillery sidewinder x1 v4 You can leave everything as it is just mount it around the existing ball bearing rolls. ... I have printed it with a brim and did NOT eliminate the brim :-D

I was running into issues with sidewinder x1 v4 build plate hitting the original mount so I extended the mount alittle further so I didn't run into this problem anymore. ...Hope this helps other users as well and saves some time of having to edit the...

a Reverse Bowden Adapter for the Sidewinder X1 V4. Parts needed: M3x10 Bolt M3 T-Nut PTFE Tube 3mm ID This Adapter replaces the Stock Filament Spool holder ontop of the Frame, and allows the Stock Filamentsensor to be used. The Sensor...

Toolbox for Artillery Sidewinder X1 v4 I designed and built this from scratch on my v4 machine, and I'm thrilled to share it with you! ... Key Features: * Five holes for each Allen key that comes with the machine * One male USB port allows you to store...

Attribution This work, "Sidewinder X1 V4 - Left X-Axis Cover", is a derivative of "Sidewinder X1 - X-Axis Cover - Artillery Logo (Now w/ Logo Insert!)" by chanh55, used under CC BY. "Sidewinder X1 V4 - Left X-Axis Cover" is licensed under CC BY by...

Attribution This work, "Sidewinder X1 V4 - Left X-Axis Cover", is a derivative of "Sidewinder X1 - X-Axis Cover - Artillery Logo (Now w/ Logo Insert!) (https://www.thingiverse.com/thing:3736048)" by chanh55 (https://www.thingiverse.com/chanh55/),...

Attribution This work, "Sidewinder X1 V4 - Left X-Axis Cover", is a derivative of "Sidewinder X1 - X-Axis Cover - Artillery Logo (Now w/ Logo Insert!)" by chanh55, used under CC BY. "Sidewinder X1 V4 - Left X-Axis Cover" is licensed under CC BY by...

Attribution This work, "Sidewinder X1 V4 - Left X-Axis Cover", is a derivative of "[Sidewinder X1 - X-Axis Cover - Artillery Logo (Now w/ Logo Insert!)](https://www.thingiverse.com/thing:3736048)" by [chanh55](https://www.thingiverse.com/chanh55/),...

A cover for the Left X axis on the Sidewinder X1 - V4. This cover permit also to hold and fix the cable to avoid burning it. And a simple plate for the opposite side. Needed : - Thread the central hole of X profile in size M5 on both profile...

  Attribution This work, "Sidewinder X1 V4 - Left X-Axis Cover", is a derivative of "Sidewinder X1 - X-Axis Cover - Artillery Logo (Now w/ Logo Insert!)" by chanh55, used under CC BY 3.0. License "Sidewinder X1 V4 - Left X-Axis Cover" is licensed...

Cable strain relief for the heated bed cable on Artillery Sidewinder X1 v4 printers. This design was inspired by Skinah's "Artillery Sidewinder X1 ac bed heater strain relief and cable chain" from Thingiverse. Unfortunately, that one did not line...

Test print for Sidewinder X1 V4 1st layer test with print area 250*250 mm plus approx. 3mm skirt distance Nozzle: 0.4 mm Line width: 0.8 mm Height : 1mm This pressure is used to readjust the pressure plate using the lower 4 screw knobs. (After...

Ein simpler Testdruck für Sidewinder X1 v4 und gleich große Drucker. Druckfläche 250 x 250 mm plus circa 3mm Skirt Distanz Standard Durchmesser Düse: 0,4 mm Linienbreite 0,8 mm Höhe 1mm Dieser Druck dient zum nachjustieren der Druckplatte...

This is my version of a gantry support for Artillery Sidewinder X1 V4. To assemble it, you will need: - 8 M5x16 screws - 2 M3x40 screws - 2 M8 threaded rods (lenght 730 mm) - 10 M8 nuts Instructions: - Fix Part A on the top of the gantry...

Toolbox to fit the Artillery Sidewinder V4 with carrier for Banggood Hex Drivers. There are two versions, one has additional venting (probably unnecessary) as the vents on the side are not covered. ... Has a lid to cover USB and Micro SD

Hemera mount for a Sidewinder X1 - there's a specific assembly order. Uses Pem inserts into the plastic in 8 locations (see *pems pic): - PemLabel00 is from a batch I bought years back. - Use a 4mm drill to clean out where the Pem goes,...

I'm so stoked about my Remix of the Unismo cover and Camstuff was exactly what I was looking for, I loved it as soon as I saw it, but when I printed it out I still kept seeing the white connector of the flex so I decided to extend the piece a bit...

Finished profiles' plates.

Upgrade Sidewinder X1 (all covers)

A popular modification for the Sidewinder X1 involves replacing the standard touchscreen with a more versatile LCD display that unlocks additional firmware capabilities. However, most LCDs come with short cables that hinder access to the board on the...

Biqu H2 mount for Artillery Sidewinder X1. With mounts for BLTouch or 3DTouch. Nozzle is in similar location to stock in X,Y. ... Attach to H2 and then to X carriage.

The original clips where made thicker and longer as the originals seems undersized on the X1 V4. The clips now fit the X1 V4 more securely. The ribbon is also held slightly better. As with the original design, this solution requires no screws ...

... is a remake of the excellent Lever design from "robscar". ...His Lever was too big for the lower ring, which made it difficult to fit into my current Sidewinder X1. ...To resolve this issue, I decided to use the same dimensions as the original design.

... the original part from fitting, I shortened it. ...The tolerances are really tight, so beware. Print Settings Printer: Sidewinder X1 Rafts: No Supports: No Resolution: 0.2 mm Infill: 15% Filament: Eryone PLA White Category: 3D Printer Accessories

This is my take on a clean setup for mounting a BiquH2 on a Sidewinder X1. So far i've been extremely happy with it, especially with how tidy the wiring is and I plan to move the probe wire inside the chassis mount as well. I started out with the...