side by customs 3d models

So, I went back to the drawing board and figured out a way to move the RepRap display forward by making the mounting to the 40 x 40 extrusion thicker from front to back. I made it 20 mm because the angle was still being taken into account. 20 mm...

she was glad to have been hired but complained about not having suitable working conditions or supplies at some of your organizations so I decided to help you guys out 'This Time' by offering some furniture and equipment that will help her be more...

As far as I know, the magnet's only purposes are to hold the data cable end in place when it's stowed, and perhaps also to serve as “screw storage” while working with the drive/case. Seagate HDD link to Amazon is an affiliate link. FAQ:Q: Are there...

 Note that the fixture should slide onto the support in the direction shown by the arrow.Once the fixture is supporting the base, the soap dish should be horizontal.C) Mix and pour the epoxy, following the manufacturer's instructions.  I recommend...

The factory sealed, hazardous location fixture is protected by a copper-free aluminum housing with an epoxy powder coated finish.The EPLC2-LB-50LED-RT is a Class I, Division 2 and Class II, Divisions 1 & 2 hazardous location light fixture that is...

 I've designed connectors allowing the planters to be joined at a variety of levels as well as fixing brackets to hang them by.There are good reasons for having ‘pods’ rather than a single hanging planter.  You can provide  optimal...

IMPORTANT:This design has been only partially tested by me; anyway this is the third iteration over the idea to reach what I consider an experimental but working/usable design. If you are one of the first giving a try to this, you will for sure have...

Here's how I went at it: Remove the case from the hotend carriage and remove the old radial fan from it Remove the top most hexagon socket screw that attaches the hotend holding plate to the plate of the carriage roller; then replace it by the long...

The foam cutter mount I remixed this from only worked with the old MPCNC.It is basically a combination of the mount for the DW660 spindle (https://www.thingiverse.com/thing:944952) and this foam cutter attachment...

By integrating it with the front section of the front receiver, I was able to give it a more flattened and, in my opinion, more aggressive look when compared with the original. It also matches the source material a little better this way. 2. In...

... Remove the top and bottom of the can by running an x-acto knife along the top (I keep the plastic lid on for this), and then along the metal bottom piece. Sand these level if necessary.160mm of 24mm (BT-50) body tube for the motor tube.Shock Cord.

so I thought of using a Hepa filter from a small air purifier on the market and adapt it to my enclosure.The aspirator filter is optional, it is only needed if your case is well sealed and does not allow air exchange.for a case such as built with...

 Lilly was the person who they called upon to put out actual fires caused by the Twins during their frequent temper tantrums.  With the threat of Lilly approaching, the twins were off scampering away, looking for their next victim. Sidney knew the...

Characterized by wings, this celestial being signifies his divine function as a bridge between heaven and earth. # Spin 5: An eminent figure in both Christianity and Islam, Angel Gabriel is known for conveying God's news to Mary about her miraculous...

### Response: Unveil the exclusive, breathtaking 3D representations of a genuine rose studio like never before. ̆ assistant # Instruction: Make the given text more attention-grabbing by adding an intriguing element, using the original text. Keep it...

- Secondly, it features an IR receiver in order to be controlled by a standard (RC5) IR remote. - Thirdly, it also features an microphone and thus, it doubles as an FFT Music Visualizer. - Last but not least, it comes with its own web interface,...

UPS charging with li-on 18650B.You can set different colors (white, red, orange, green, blue and yellow) by button ON/OFF. Buttons LIGHT+ and LIGHT- are for brigthness control.</p><p>In the base is UPS charging with li-on 18650B (<strong>not...

But this way it's more in line in how the pegboards are supposed to work.Parts included (for now):mini-ITX motherboardGPU mounted vertically on a riser cable (screw holes for 3 slots)PSU (HDPLEX 400W HiFi DC-ATX + AC-DC combo)power button (the very...

Spin with a maximum of 60 words: Gifted with exceptional guitar skills, John graces multiple musical groups with his presence. assistant John, an accomplished guitarist, showcases his talents by performing in numerous bands across diverse genres. ...

My daughter loves playing chess, but the magnificent pieces by NTX9 often fall out the original box when she tries to relocate.Therefor I made a remix that allows for a lid to slide in front of the pieces. The lid is of course based on the pieces...

When you've got the time to waste and a 3D printer sitting idle you use a cheap 6mm laser (less than $10 for 10 pcs online) which is badly aligned and poorly focused, print this thing and do the alignment by hand. <s> It's only 4g of filament (1.43m...

This support allows rotating easily the camera. Besides the cover itslef, two new LCD support parts are included to attach the cover to the same screw holes already present in the printer. Hardware A Raspberry Pi 3 Model B+ has been used as the...

UPDATE 3 (regarding Wanhao Duplicator i3/i3Plus):\nI highly recommend replacing the bearing rods and generously applying MoS2 grease to the inside radius of the original linear ball bearings for maximum quietness and lower friction.\nThe greased...

If you find some please contact me so I can update the link!Mini USB C dock with HDMI and USB 3.0 https://www.amazon.de/gp/product/B08SM2QVXS/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1Short HDMI cable (...

After assembly, I put a bow in the wing to help stabilize flight and make it look kind of like a Hobie wing by simply bowing up the wings a few inches and taping them in place and let set for 24 hours. When you take the tape off, there is a nice...

The fastening clip can be opened by 2-3 mm or opens independently when pushed in. The inner diameter is ⌀ 6 mm.Don't have a 3D printer? ...Feel free to write me your wishes or suggestions on https://www.instagram.com/druckdrei/ to improve your coffee...

I have originally posted this THING on the Facebook user group [Laserpecker 2 User Group (Unofficlal)](https://www.facebook.com/groups/lp2users/), run by [Michael Atkinson](https://www.thingiverse.com/minhraju/designs). If you do not already belong...

The mask can be moulded slightly by heating the shell with hot water or hot air and bending the edges carefully. The TPU seal can be used to fill some of the extra gap for those with smaller noses and lower bridges than mine. <b><u>Summary</u></b>...

I wanted to print this awesome design by HexiBase on my Ender 3 but the two halves were too big to fit on the build plate so I split each one into two smaller sections. The two sections are joined together via a tongue and groove arrangement, making...

- [Ultimaker Cura](https://ultimaker.com/software/ultimaker-cura/) is free, easy-to-use 3D printing software trusted by millions of users. Fine-tune your 3D model with 400+ settings for the best slicing and printing results. This model has been...