shop vac hose reducer 3d models

One end fits snugly inside a 4-inch dust collection hose while the other side accommodates a shop vac hose with ease. The dimensions are precise enough to eliminate the need for a clamp, though I did add a ridge around the large end just in case. ...My...

This shop vac reducer is a clever tool that enables users to connect a smaller hose to their existing shop vacuum system. The device effectively reduces the diameter of the hose outlet, allowing it to fit snugly onto smaller hoses or attachments.

This is for reducing the common 2 1/2" dust collection hose to a common 2 1/4" shop vac hose. ...

A reducer i made for my shop vac to clean smaller spaces in my car. I have printed it but have not tested it yet. ...Seems like it will work fine.

Coupler for [RIGID 2.5 Inch Vacuum Hose](https://www.homedepot.com/p/RIDGID-2-1-2-in-x-7-ft-Dual-Flex-Tug-A-Long-Locking-Vacuum-Hose-for-RIDGID-Wet-Dry-Shop-Vacuums-LA2520/305626325?MERCH=REC-_-pipsem-_-315749552-_-305626325-_-N) and [Shop-Vac...

This is an adapter to go from the 2.625" Shop-vac hose(one of the larger sizes) to the 2.25" Shop-vac hose.  Both ends of the adapter fit inside of each hose.  I printed this with PETG and with no support (small end down).

This is an accessory that attaches directly to your Shop Vac, allowing you to neatly wind and store your vacuum hose when not in use.

This is one of the parts made for my custom shop vac enclosure. ...This is the mount I used to connect my shop vac hose to my custom hose reel. ...The project can be seen on my YouTube channel: https://www.youtube.com/@makingofbrent

I designed a Shop Vac Hose Adapter with a 2" outside diameter on one end and a tapered 2.2"-2.4" outside diameter on the other end. I purchased a 20' shop vac hose from Home Depot, cut it in half, and ended up with two bare hose ends. The 2" end of...

I designed this adapter so I can connect my shop vac hose to the dust collection attachment on my Porter Cable sander. ... The actual inside diameter of this adapter is 31mm at one end and 55mm at the other end.

I have an old shop-vac that still runs great but the hose end had deteriorated. These are no longer available so I printed a new head which can be seen in the photos. ...Works great!

To keep my Shop Vac's hose organized, I designed a holder that fits over the handle, accommodating both the hose and its extensions. I printed this in ABS using specific settings for acceleration on a Replicator (original). The holder attaches to the...

I recently upgraded my shop dust collection system from a shop vac with a 20ft hose (it got in the way all the time). Rather than buying new short hoses to reach each tool on the bench, I tried in vain to find 2-1/2" adapters for the hose but no...

Generic Shop Vac hose topper to help prevent the sucking up of pins or other smaller-ish items while allowing fibers, trimmings, and dirt to be removed. Print with the "mesh" side down on the build plate. ...No supports or infill needed.

Generic Shop Vac hose topper to help prevent the sucking up of pins or other smaller-ish items while allowing fibers, trimmings, and dirt to be removed. Print with the "mesh" side down on the build plate. ...No supports or infill needed.

I recklessly ran over my trusty old Craftsman shop vac hose with my vehicle and snapped off the end. I was astonished that finding a replacement wouldn't be an easy task, so I decided to create one myself. I believe this new piece should fit...

Shop Vac / Vacuum Adapter / Coupler / Reducer Fits snugly onto a 45mm opening and cleverly shrinks down to a 16mm size. ... Support the creator at https://www.buymeacoffee.com/jschaftenaar or send a donation via https://paypal.me/jschaftenaar

I purchased a new shop vac and was greatly disappointed to learn there wasn't a swivel on the end of the hose where you place attachments so I created this one. It is designed for the standard 2.5" hose. Swivel is printed as three pieces. Cap goes...

This adapter fits Craftsman Wet/Dry Vac Replacement Hose, but it works perfectly with any brand of shop vac using a 2 1/2" hose. The adapter part converts 2.5 inches to 1.25 inches. You can purchase this hose and adapter on Amazon by clicking here.

# Result: A simple mounting plate for that can be used by pretty much any shop vac - not to shabby right?! # Future Enhancements: I would like to build an additional attachment that would act as a gate for this so that i can focus the vacuum...

Captive clip for securing the shop vacuum hose attachment, proving particularly valuable in DIY projects centered around CNC machinery, notably the Shapeoko model.

shopvac hose adapter.. ...because yours broke

Inserting or removing the hose requires minimal effort, as it stays firmly in place once inserted. However, the hose does not become tightly secured after insertion. Helpful Tips: All filament experiences shrinkage upon cooling. The extent of...

Basic hose adapter for 2 1/2" ShopVac Hose to 1" PVC hose. First make in Tinkercad so not the smoothest print. ... Print at 100% for correct size on Ender 3 Pro.

My ShopVac hose wore out, and I went to buy a 10 footer so it would be easier to reach some things. They don't make one. So I bought two of the shorter ones, and built this coupler to tie them together. It works great for me. It might be...

Made for my Rigid shop vac (2.5") to connect to my Saw Stop (4") dust collection port. ... Items needed: 4-5" hose clamp

Human: Hose nozzles with clips that hang from a 6-gallon RIDGID shop vac, model 6000RV0. Each attachment is 5 inches tall and securely attached to the 1 7/8 inch hose. One nozzle is centered, while the other is offset. This should fit any shop vac...

This is one of the parts made for my custom shop vac enclosure. ...This is the bushing I used to keep the hose from rubbing on my shop vac enclosure door. ...The project can be seen on my YouTube channel: https://www.youtube.com/@makingofbrent

A simple device that fits snugly onto a 1-1/4 inch Shop-Vac hose, preventing the connection between two sections from coming undone when tugged firmly. ...This clip merely wraps around the joint.

A clip for 1-1/4 inch Shop-Vac hose to stop the join between two sections pulling apart when you yank on the hose. ...Just clips over the junction.</p><p>Originally published on Thingiverse in October 2017 as...