shock mount tabs 3d models

This is a shock mount to be used on the Sony FS5 camera. With the use of standard O-rings, a shotgun microphone is suspended in the middle. ...Elastic cord can also be used instead of O-rings.The regular mount that comes with the camera often becomes...

This is a shock mount to be used on the Sony FS5 camera. With the use of standard O-rings, a shotgun microphone is suspended in the middle. Elastic cord can also be used instead of O-rings. The regular mount that comes with the camera often becomes...

Just keep all the parts form your microphone handy just in case this doesn't work. Also, you'll need to add a 1/4" - 20 nut in the base in order to mount it to a tripod. Print instructionsUnassociated tags: easy print, go mic, samson go mic, shock...

... I would probably recommend printing the ring at 100% infill for additional torsional rigidity. It works beautifully and I couldn't be happier, especially considering that it cost me $15 to make compared to $50+ for the Blue Shock Mount on Amazon.

To reduce camera noise interference, I crafted a shock mount for my Sony EX-1 microphone with a maximum length of 5 CM, though a 7 CM version is also available. This two-part design eliminates the need for support material and requires only male and...

I have a MOVO shock mount that I adapted to use with an Elgato Wave 1 mic, but it felt too floppy, so I designed a little extra support. I used a little hair band as the elastic part. Printed PLA at 0.2mm with 100% infill and a brim. ... I was able...

This is a compact shock mount designed for shotgun microphones, with the T.Bone Em9600 being its intended target, but it should be compatible with most models. The design allows users to employ a rubber band of their preference. On one side, you...

This makes it easy to remove and reattach if you want to transport just the microphone and not the entire shock mount. All you need to do is print additional exteriors! One issue with this microphone is that it's very heavy. While this contributes...

I broke the shock mount that came with the microphone, and I think a replacement is too expensive - so I created one that's probably better. All you need is a 5/8 Nut for the standard microphone stand (North America) and some shock mount elastics. 2...

A 3D image of the back shock bracket on an '08 Rabbit car.

Relocating shocks enables you to adjust their position for improved suspension articulation.

If You Already Have A Shock Mount, You Can Stick With The Original Rubber Bands Or Swap Them Out For Regular Ones, As Long As They're Taut Enough. This Is The Revised Version Of This Concept - The First One Was Way Too Bulky. I Managed To Cut Down...

This is a small shock mount for shotgun microphone. The one I made it for is the t.bone Em9600, but it should work on most. Its made so you use rubber band of your choice. On one side you can hook the ends of a small rubber band, if you dont have a...

This shock mount is designed specifically for use with the Samson Go Mic. When combined with the shockmount_monitor_cup.stl file, it can be securely clipped onto a monitor stand with an outer diameter of up to 5cm. If you wish to attach the mount to...

This is a simple but good microphone shock mount for Aston Origin. Found a few designs here on Thingiverse but i couldn't find one that wasn't to big or it needed several screws and parts to assemble. so i designed this out of what i found here...

A basic fixture for securing a relay module to the shock absorber assembly of a Suzuki DRZ 400 motorcycle.

A sleek and compact handheld shock mount specifically designed to accommodate a Rode NTG1/2 mic, also compatible with mics featuring a diameter of approximately 22mm or smaller. Fitted with a standard 3/8" nut in the base of its handle for...

Inspired by Mic zoom h1 holder by Rukey and Rode Shotgun Shock Mount. ...Parts should be glued together.The tripod screw is supposed to cut itself into the hole.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>MakerBot</p> <p...

A high-end handheld shock mount designed specifically for the Rode NTG1/2 microphone, although it should fit any mic with a diameter of approximately 22mm or less. It features a 3/8" nut in the base of the handle, allowing for standard mic pole and...

Shock Mount for Aston Starlight Mic: Inspired by Thingiverse Design Version for Aston Origin Available Here: https://www.thingiverse.com/thing:3377783 The Ring Thickness Should Match the Included Mic Holder on Aston Starlight I Had to Sand Mine...

This shock mount is for the *Samson Q2U* microphone. I saw some other designs that used hair bands to locate the mic body. I was intrigued to try that for myself. I found the mounting rings a bit clumsy, therefore I designed my own. As you may be...

A Nema 17 shock absorber is an essential component for various applications, providing smooth and controlled movement while reducing vibrations. It is widely used in robotics, CNC machines, 3D printers, and other machinery that require precise and...

Normally a steel tube strenthens the bolt in a wider mounted shock end, in that case one can probably also adjust this design via parameters to be just the spacer. Print Settings Printer: Ok Rafts: No**Supports:** No Resolution: 200**Infill:** 95%...

This shock mount is for theSamson Q2U microphone. I saw some other designs that used hair bands to locate the mic body. I was intrigued to try that for myself. I found the mounting rings a bit clumsy, therefore I designed my own. As you may be able...

I'm Excited to Share My First Design Attempt, Where I Experiment with Repositioning Shock in Various Locations - Filling 50% of the Space. Please Try It Out and Let Me Know What You Think! ...Your Feedback is Highly Valued, and Feel Free to Remix It to...

Designed especially for TPU filament, with double rycon mount system.

All assemblies revised and primed for printing! ...A, B, and C mounts now function as secure screw fasteners.

... from being conducted. Bill of Materials: Two O-rings with an inner diameter of 24.5 mm and an outer diameter of 30.5 mm Two rubber bands with an outer diameter of 25 mm One camera screw (¼ inch) One suction mount or any suitable camera mount

This is a remix to allow for a hex nut to be used to screw to a standard 1/4"x20 camera mount instead of a cold shoe mount. The hole is undersized and will need to be drilled out with a 1/4" drill bit or similar. ...The hex hole is slightly oversized...

The stock BOYA BY-MM1 microphone mount is way too stiff to do any good. The Rycote Lyre stye design is way too soft printed in TPU. ... This my modified Lyre design to be printed with TPU.