shirt 3d model

- You can find a somewhat more detailed list of supplies in my Instructable at https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Basically any combination will do (as long as the driver is 3.3" or smaller so it fits...

It is essentially based on my first design.If you don't have an AC Infinity T8 or don't want to spent 120 bucks on one just to disassemble it, check out this simpler and cheaper...

As applicable for all home brewed masks with a filtering purpose: this model is not tested by given standards, the functionality is not verified, and it’s not certified in any manner. Be aware of the risks and use it on behalf of your own...

My model was FDM printed only. Actual code will be available here: https://github.com/Kandzior/NeverHotTeaAgain Charging is done by plugging micro-usb cable to the charger module through hole at the side. When you disconnect the plug, you can cover...

Knob channel.stl - channel knob, for 16 position rotary encoder, model unknown, mine was from professional 16-ch radio. 7. Antenna.stl - old-style, PRR mock antenna. 8. Antenna New.stl - new style, EZ-PRR mock antenna. 9. PTT Lemo Single.stl - PTT...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Printing Recommended slicer settings: Resolution: 0.1mm - 0.2mm Infill: 10% - 20% Supports: Doesn't Matter Rafts: Doesn't Matter License The "Customizable Arduino Nano LED Candle (2 - 6 LEDs)" model (.stl) is licensed under the CC BY license by Code...

Check out the Raspberry Pi 3B+ here: https://www.raspberrypi.org/products/raspberry-pi-3-model-b-plus/ The controls are simple but there's enough buttons for most games. D pad for direction control and 4 front buttons provide your basic SNES type...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

IntroductionThis model provides an effective, low-cost teleprompter for livestreaming and recording. Using a Raspberry Pi and Pi Camera (the cheap, non-HQ one provides great full-HD video in this application), your phone to display your script or...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 67 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

Load your Model into PrusaSlicer and assign both materials. Prusa provides a quite helpful database on their website on how to use all the features in their Slicer that are related to multi-material-printing. After changing the filament there is...

If they are different, please update the Fusion 360 model and re-generate the toolpaths. Also, if you plan on using different tools for the above operations, make sure you update the tools (and associated feeds and speeds) and regenerate the tool...

Depending on the figurine put on top of the box a different playlist ist played, currently mostly kids audio books and a spotify music playlist.All in all a very cool project that i hope to expand when my son grows older.ElectronicsPhonieboxRaspberry...

UPDATE: 20.04.2022adapterplate (new design) for model C Hello, we would like to introduce you to our stealthburner conversion mod. At this time it works only with the klipper Firmware. The use with “Marlin” is planned later and will be...

Able to hold 1 stack of cards and 2 columns of hexes. --4-2-17-- Added player card 2.2, a little bit smaller on the separator pieces that come off the model, should be easier to fit in the box. --4-2-17-- Removed older hex and cards .stls and...

Printing time is &gt;15min.Credits:The original configurable OpenSCAD model is by wstein, posted here. ...Thank you Werner!</p><p>Thanks to <a href="https://www.printables.com/social/78665-darktiger/about">darktiger </a>for his print and picture of the...

The original interior geometry from the Prusa filament sensor has been incorporated into this design, sourced from Prusa's models. The pinda is in the same location as on the original. The nozzle in this new design sits 10mm further forward along the...

Four screws for every corner and 8 screws for every side.[blue] NO acrylic glass holder at the side where the hinge mechanisms are located!From this on the “Front” is where the hinges are.[green] At the location of the green circle you can drill a...

Or rather, it's a scale model of what that house looked like fifteen or twenty years ago. The wrecked version is closer to how it looks now that it's been abandoned for the better part of two decades. The tweakers have had a field day with this...

You may have to do some light cleanup, but the fit of the parts should be snug enough to hand press together with no wobble. IOMarms STL- These arms are taken directly from the original wood designs and are generally sized for an IOM, but are not for...

The use of simple metal parts in combination with printed components holds a lot of potential for the future; FreeMenDontAsk is already working on other handgun models. Even outside of gun making, this could be useful for a wide array of printed...

We are modelling the *BELT* tooth here, not the tooth on the pulley. Increasing the number will *decrease* the pulley tooth size. Increasing the tooth width will also scale proportionately the tooth depth, to maintain the shape of the tooth, and...

The design is a complete rework of my older oscillating fan model.It uses a common 130 size brushed hobby motor and incorporates an 18650 battery in its base for completely portable operation. Compared to the older design, the new version has...

rice or sand.Glue if the press fits are not tight enough&nbsp;Testing tolerancesStart by printing the models press_tolerance_test and rotation_tolerance_test from the folder Common parts.Press fit toleranceUse the press fit test to decide which press...

Model says 119mm, which would be close.???---------------------------------------------------------------------------------------------------------Printed Parts:&nbsp;Base:___________________Placeholder____________________This is the base of the...

It deviates a bit of what I usually call an "sci-fi astronomical object", because it's an in-spacecraft transport vehicle. I made this model available in 4 scales. I left the model in "halves" that I consider the best way to print it, of course, with...

Remove the stock z-axis tops and replace with this light bar mount.Single Mount Z-Axis Top No Switch: Same as Single Mount Z-Axis Top with no hole for the power switch.&nbsp;Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill: 15%...

If do you need to get the lock back off, the best way I found was to stick long allen keys into both of the lock's holes and then pinch them together to lever the lock slightly apart, which reduces the pressure enough that you can wedge a thin...

Potřebné vybaveníNotebook nebo tablet, programy Tinkercad a PrusaSlicer, 3D tiskárna.Nepovinné - krabička čtvercových rozměrů, tvrdý papír, pravítko, tužka a nůžky (viz postup).9. Potřebné soubory a dokumenty (seznam...