shimano crank arm 3d models

*untested Shimano crank arm fixing bolt remover tool Interior slot for 6mm hex key *I don't own a 3d printer and haven't been able to validate tolerances

Needed the tool that screws off the crank arm cap for a Shimano SLX crankset, so instead of dropping between $10 and $20 for a tool I decided to make one. Snapped a top down pic of the cap, modeled the inner splines in Fusion 360 and went from there....

This adapter enables compatibility between regular square taper crank pullers and Shimano Octalink/ISIS Cranksets. ...Given its common misplacement, it likely experiences frequent loss among users as well.

[If you find my designs useful, please consider sending a tip](https://www.paypal.com/paypalme/slegnor/1) Simple dust cover for my wife's Giant Boulder Shimano FC-TX70 Crank, using the 8 mm hex fitting to hold it in place. ... Print Settings: ...

This mount allows you to attach Wahoo's RPM Cadence sensor directly to a Shimano Ultegra 6800 crankset, making it easy to install and modify for various other setups.

The project remains unfinished; the term "freeform surfaces" may not be entirely precise. Nonetheless, the dimensions align with those of the actual component. This model can assist in planning aspects such as chainline and q-factor, as measurements...

Shimano Hollowtech 2, Ergonomic Crank Tool

It's adapter on 1/4" squer wrench to mount Shimano Ultegra crank cup.

A versatile hand tool designed for removing two-piece crank arm caps, much like the TL-FC16 from Park Tool. Perfect for Shimano Deore XT cranksets and other similar designs. ...Easily removed by hand or with a 6mm Allen wrench, this simple yet effective...

RaceFace and Sram sells crank boots for Sram carbon cranks. ...This is the same item, but with Shimano aluminium crank dimensions; verified with XT M8100 and SLX 675. ... Use TPU as a filament and 100% infill.

To tighten my Shimano crank bolt, I made a straightforward adapter for transforming it into a hex driver. ...The fitting was spot-on during the initial attempt!

For Shimano Alivio M4050 M4060 Printed with pet-g, no supports, fits perfect

For Shimano Alivio M4050 M4060 Printed with pet-g, no supports, fits perfect

This is a tool for removing/installing the preload cap on a Shimano Hollowtech II bottom bracket. ... Print Settings: Printer Brand: LulzBot Printer: TAZ 5 Rafts: Don't worry about it Supports: Don't worry about it Resolution: 0.2 millimeters Infill:...

Crank Arm

Hand tool for removing the crank cover on Shimano 105 groupset bike. ...Probably fits all Shimano variants

Rixtronix LAB Crank Bolt ShimanoV1.8.40.9.2.23 M20x20 9Feb23 20mm Shimano spline 1mm Pitch

crank

For removing crank cap.

Simple Shimano crank cap tool inspired by the design by T70E. This one is closest to the original, and I like it because it's really small and does not take up much room in a tool box. (see the photo with an earlier prototype in my toolbox) Very...

The spacer fits snugly over the end of the crank spindle and enables the "fixing bolt" to apply even pressure against the crank arm via the spacer, ensuring proper pre-loading of the bearings. To achieve a Q-factor as low as 2.5mm narrower, some...

Simple Shimano crank cap tool inspired by the design by T70E. This one is closest to the original, and I like it because it's really small and does not take up much room in a tool box. (see the photo with an earlier prototype in my toolbox) Very...

A LH crank arm is specifically designed for a Rocky Mountain Vapour bike, ensuring smooth and efficient pedaling performance.

For removing crank cap. ...Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter Category: Tools

Printing settings is next on the agenda after replacing crank cap. ... Settings: Printer Support Supports: Raft Mode Raft settings: Doesn't Matter

Need to replace your crank bearing on your bicycle? Then this the tool for you. It should work for both sides of the bearing and is surprisingly strong but may also fail for some especially tight bearings. ...Using it as is requires a 24mm hex socket...

For further inspiration, browse these alternative crank arm designs on GrabCAD https://grabcad.com/library/crank-arm--1 or https://grabcad.com/library/crank-arm--3. **Printing Settings:** - Printer: Flashforge 3D Dreamer - Rafts: Yes - Supports:...

Shimano Crank Installation Tool Specifically Designed for Hollowtech II Systems

Crank protector for shimano M8100 and SLX675

This is a Shimano crank installation tool designed specifically for use with Hollowtech II systems.