shimano 10 speed cassette spacer 3d models

Spacer that fits between cogs for a 10 speed Shimano cassette. Mileage may vary with SRAM/Campagnolo cassettes - see design section. Pretty sure it'll be strong enough. I'll let you know if I have problems. Print Settings Printer Brand: LulzBot...

I referenced my 7 speed cassette on 8/9/10 freehub 4.5 mm spacer for the OD & ID. Assembly Note that there are no notches in this piece that fit over the splines of the freehub body. I never understood why spacers needed these, & it just made the...

Cassette spacer for 9-speed Shimano bike cassette. 2.56 mm. ... Outer diameter 40mm, so will fit any cog 12T upwards.

Some 9 speed cassettes come with individual cogs separated by plastic spacers. I inherited one of these but it was missing a spacer. The required spec is here.Sram: 2.54mmShimano: 2.56mmI designed this to be 2.56mm thick, but in practice, printers...

Same outer dimensions as the cassette holder by julienpmorand, just hollow all the way through to save on filament.

See http://www.thingiverse.com/thing:2064758 This one works with Shimano & SRAM cassettes. ... Category: Replacement Parts

Check out this project on Thingiverse - http://www.thingiverse.com/thing:2064758! ...It's specifically designed for use with Shimano and SRAM cassettes, making it a great solution for those who need a reliable fit.

This is a 2.35mm Cassette Spacer designed specifically for 10 speed cassettes. **Critical Printing Note** To achieve the best possible performance from your cassette, print this spacer on a machine with extremely high tolerance settings. I printed...

I created this spacer to fit a Shimano cassette bicycle rear wheel because my gears cassette was significantly shorter than the hub. The inner part features the distinctive Shimano tooth pattern, while the disk extends slightly outward from the...

I designed this spacer to fit a Shimano cassette bicycle rear wheel, because my gears cassette was shorter than the hub. The inner part has the shimano tooth pattern, and the disk extends a bit outwards of the external gear so as to avoid the chain...

1.85 mm wide spacer for mounting 8/9/10 speed cassettes on an 11 speed freehub body. Stuff from here may apply: http://www.thingiverse.com/thing:2064758 How I Designed This http://problemsolversbike.com/products/cassette_spacers Pulled 1.85 mm width...

I'm designing a spacer that's specifically made for mounting 8/9/10 speed cassettes onto an 11 speed freehub body, and it measures 1.85 millimeters in width. You can check out some information on this topic at...

Illustrations depicting a Shimano 7-speed gear cassette are displayed in the design.

A 3.5 mm spacer (worked better than 3 mm) to mount 7-speed cassette on a 8/9 speed hub, None of the models found on thingiverse featured the rivet holes as seen in in [2] and [3] Went over 3 iterations. At the end I got a tight fit of the spacer...

I printed a new spacer late at night for my bike because the one provided by the shop was too thin to fit properly on an 8 speed rim with a 7 speed cassette. The spacer isn't under stress since the cassette meshes perfectly with splines on the wheel....

Shimano 8 speed cassette holder for convenient storage. The measurements consider the expansion of the ABS for a precise fit that secures the cassette in place. Results may vary depending on the plastic and your printer (see print settings). ... Print...

Shimano 10 Speed Cassette Holder for Easy Storage and Organization, Designed with Precision to Fit Perfectly. The measurements of this holder take into account the natural expansion of the PLA material used in 3D printing, ensuring a precise fit...

This spacer is designed for use with the Campagnolo cassette, 11 speed. Sizes are:- 2.2mm in thickness. 40.75mm outside dia and 36.25mm inside dia. This size is a snug fit onto the cassette centre shaft, but if required, you can enlarge the...

This is a spacer that fits on Shimano or Sram hyperglide (the most common) freehubs. Included are several thickness parts, as well as a DXF drawing from which you can extrude any width. If you make your own part I recommend adding a 0.25mm chamfer on...

This is a compact 4.5 mm spacer designed specifically for installing 7 speed cassettes onto high-performance 8/9/10 speed freehubs. ...Visit Jensonusa.com to learn more about Cassette Spacers today.

This is a 4.5 mm spacer for mounting 7 speed cassettes on 8/9/10 speed freehubs. http://www.jensonusa.com/Cassette-Spacer Very simple. ... Category: Replacement Parts

Check out this awesome project on Thingiverse at http://www.thingiverse.com/thing:2064758

See http://www.thingiverse.com/thing:2064758 Category: Replacement Parts

This is a very rough model of an 8 speed shimano cassette. Actual sprocket geometry not existent. ...Cogs are 11, 13, 15, 18, 21, 24, 28, and 34.

My trainer came with a pre-installed Shimano 105 (or equivalent) 11-speed cassette mount, which was just too wide for the 7-speed cassette sprocket I wanted to mount. Print with some really strong material at 100% infill. I use a <a...

Realistically, you could make this into spacers to convert a freehub into a single-speed.I'll include STL, 3MF, F3D files at a minimum. The design was in Fusion 360.PRINTINGI printed in ABS+, but probably PLA is just fine. Layer height can be pretty...

Replacement star spacer for Shimano SLX M7000 11-Speed Cassette. Not an exact replica, slightly larger and added an outer ring to prevent the scenario that led to the original part getting snagged and broken. z The inner teeth are intentionally...

Replacement star spacer for Shimano SLX M7000 11-Speed Cassette. Not an exact replica, slightly larger and added an outer ring to prevent the scenario that led to the original part getting snagged and broken. z The inner teeth are...

Cover for the bottom of the Shimano Deore M4100 10 Speed shifter mounted on the right. Might be able to be used on other shifter models, but I haven't been able to check. I also don't know the correct orientation for printing. That's up to you. ...If...

... until next week. ...To keep my ride going, I whipped up a custom fix using petg - the print works fine since the stress is minimal. Any material would do for this part, really. The official name for this piece is SHIMANO SLX M663 10 SPEED PULLEY SET.