shendrones 3d models

Remix of Andy's DJI VTX antenna mount, it uses a MMCX Male to SMA Female Length: 80mm pigtail adapter. ...I purchased here: https://www.racedayquads.com/products/rdq-mmcx-pigtail-90-mmcx-to-sma-pigtail?_pos=1&_sid=a05bd3e5b&_ss=r I also used this...

Home made SMA mounting bracket connects to stand-off.

This mount attaches a Gopro tab to the top of the krieger, requiring the low profile frame for the gopro session and shorter thumbscrew. Print Settings: Printer: Wanhao Duplicator i3 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2mm Infill: 20%...

Proper protection for LiPos upon landing is crucial to prevent damage and ensure a successful landing procedure.

Print the base in a durable PETG or ABS material and the camera mount with servo in flexible TPU. ...The design requires a sturdy 10mm outside diameter / 5mm inside diameter bearing and a robust 5mm x 25mm standoff.

This is a custom-designed side panel cover for the Shen Drones Tweaker 180 quadcopter. Feature Set Easy snap-on design that eliminates the need for additional hardware Extends across the left or right stand-offs without interfering with the...

Mount for 10mm diameter caps and the GPS Matek M10 5883 11/03/2023 Edit: -Added a version for a 16mm dimater Caps and Fettec Spike Absorvers

This is a component that I developed to facilitate mounting receiver antennas onto the Shrieker. Its purpose is to guide the antennas through the two openings at the rear, then simply insert a small zip tie (with the tapered end facing forward) into...

The Rapture's Session and Runcam mounts are securely fastened in place. Printed with precision on a high-quality TPU material, these components provide a solid foundation for the system. ...A sturdy battery strap expertly holds everything together,...

I've found a way to keep my Tweaker XT60 Holder in pristine condition with its sleek LED design. A discreet hole on the backside allows for effortless cable management, keeping everything organized. To complete this setup, I recommend using Banggod's...

Fabricated an interim top plate for my Tweaker as a temporary fix, pending replacement of the original.

This mount is designed specifically for use as a standoff when working with non-standard square form factors that incorporate ESC pads and the like. ...It features pre-threaded M3 holes, making it essential to print this item at a high resolution and...

Tweaker 180 XT60 Saver You probably need to tap or hone the holes slightly. The XT60 connector may be stuck on due to adhesive. ...Enjoy!

<p>This is a remix of the original design, printed with no supports in PETG&nbsp;</p>

Front-end Mount for Squirt Servo with SG90 Servo. Required: (2) 10mm OD / 5mm ID bearings (1) 5mm Diameter shaft, 35-40mm long (1) Paper clip or piano wire to secure the servo and session together, with a small hole in the corner of the session. ...

I don't own a siccario myself, minor adjustments may be done in the future. You can print it in 95A TPU, but I recommend using ninja flex or similar to get maximum adherence. ...You will have to glue the pad using contact cement or a similar flexible...

This is my high-performance race pod for the Shen Drones Mixuko 5" frame. The pod is engineered for a very short, tight 30x30 stack (FC and 4in1 esc) and a micro camera with a 12mm diameter lens (I'm using a Swift Micro V2). It features a designated...

This is my radical race pod for the Shen Drones Mixuko 5" frame. This pod is designed for a very short/tight 30x30 stack (FC and 4in1 esc) and a micro (19mm wide) camera with a 12mm dia lens (I'm using a swift micro v2). It has a place for a TBS...

Hoops and Mini ducts for the Squirt V2, that improves the fly experience. There are two different models: -Some hoops to whom doesnt like ducted drones. ... -Mini ducts -Ultra Mini ducts (5mm less) If you like it, visit my 3D printing web: ...

Mixuko 5" Runcam Micro Swift Camera mount. Designed to be printed in PTU so there's flex and can be "pinched" between the side frames. This replaces the carbon camera mount that has always been a pain to keep from wiggling and to keep the camera...

Print with TPU

This Hero 8 Rear Mount for the Geyser is engineered to secure itself to a customized antenna mount (supplied) using a coarse screw (I'm fairly certain it's a #10-32, but I've included an image of it)\r\nThe mount also wraps underneath and fastens...

Mount a GoPro on your drone with ease using this sturdy reinforcement plate designed to withstand rigorous flight conditions. ...Print it out in durable PLA or hard plastic, and don't forget to upgrade those screws for added stability.

So being the meticulous miniquad builder that I am, I was worried about the battery sliding forward and the cells or leads getting cut by the stack cover plate on the Ichabod Jr. So, I designed this 'Battery Bump Pad' as a gentle surface for the...

I thoroughly enjoyed the original layout, but didn't want the added bulk of the standoffs, so I extensively reworked the design, merged both components together, made the camera tilt adjustable from zero to twenty five degrees, and altered the shape...

This is a remix of https://www.thingiverse.com/thing:4008135 but at time of posting, Thingiverse's remix feature doesn't work. The original wasn't compatible with GoPro thumb screws and required a 20mm m5 bolt. In this version, the m5 nut is...

**Please comment on here and let me know how it works out. It will help me improve and provide to this community. I put a lot of thought into these, even the miniscule details and i hope it reflects in my descriptions. My goal is to make things...

Clean up your thicc build with this AS150 connector mount for + and - connections. ...Printed with ninjaflex tpu at 30% infill with good results.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/4fUbLZLXOHl

The Rear is remixed from https://www.thingiverse.com/thing:2796363 also includes a 15 Degree Wedge that allows you to change the front cam angle to 10 Degrees DOWN (instead of 5 degrees up) Shendrones GeyserPhobe from QSL...