shendrones terraplane 3d models

This is a remix of amfromch's lipo protection to extend the battery strap lifespan. Removed 1mm from the bottom layer to snugly fit the battery strap, adding 4 small feet for stability. Print cover at 1.0 scale PLA. Print feet between 1.0 and 1.1...

Mount a GoPro on your drone with ease using this sturdy reinforcement plate designed to withstand rigorous flight conditions. ...Print it out in durable PLA or hard plastic, and don't forget to upgrade those screws for added stability.

Here is the camera's features. The 8MP image sensor captures sharp, detailed video in any lighting conditions. A wide 170-degree viewing angle and high-quality 14mm lens capture every moment. The PAL and NTSC modes let you record at up to 600TVL...

Remixed the original Siccario front and back shirts to be shorter to allow routing motor wires when braided or wrapped. Also including a version that is better compatible with the stand-alone DJI FPV heatsink mount. ... Original designs from...

I don't own a siccario myself, minor adjustments may be done in the future. You can print it in 95A TPU, but I recommend using ninja flex or similar to get maximum adherence. ...You will have to glue the pad using contact cement or a similar flexible...

This is my radical race pod for the Shen Drones Mixuko 5" frame. This pod is designed for a very short/tight 30x30 stack (FC and 4in1 esc) and a micro (19mm wide) camera with a 12mm dia lens (I'm using a swift micro v2). It has a place for a TBS...

A top plate of 2-part was demanded to be crafted for the Tweaker system.

That's a prime opportunity for mounting Foxeer Legend 1 cams on the Krieger. Flexible filament is highly advisable, as I didn't test this case with rigid filament, so it likely won't fit properly. ... Print Settings: Printer: TinyBoy Rafts: Yes ...

Hoops and Mini ducts for the Squirt V2, that improves the fly experience. There are two different models: -Some hoops to whom doesnt like ducted drones. ... -Mini ducts -Ultra Mini ducts (5mm less) If you like it, visit my 3D printing web: ...

Mixuko 5" Runcam Micro Swift Camera mount. Designed to be printed in PTU so there's flex and can be "pinched" between the side frames. This replaces the carbon camera mount that has always been a pain to keep from wiggling and to keep the camera...

Print with TPU

This mount attaches a Gopro tab to the top of the krieger, requiring the low profile frame for the gopro session and shorter thumbscrew. Print Settings: Printer: Wanhao Duplicator i3 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2mm Infill: 20%...

Proper protection for LiPos upon landing is crucial to prevent damage and ensure a successful landing procedure.

This is a custom-designed side panel cover for the Shen Drones Tweaker 180 quadcopter. Feature Set Easy snap-on design that eliminates the need for additional hardware Extends across the left or right stand-offs without interfering with the...

I've found a way to keep my Tweaker XT60 Holder in pristine condition with its sleek LED design. A discreet hole on the backside allows for effortless cable management, keeping everything organized. To complete this setup, I recommend using Banggod's...

This is a remix of https://www.thingiverse.com/thing:4008135 but at time of posting, Thingiverse's remix feature doesn't work. The original wasn't compatible with GoPro thumb screws and required a 20mm m5 bolt. In this version, the m5 nut is...

Fabricated an interim top plate for my Tweaker as a temporary fix, pending replacement of the original.

Tweaker 180 XT60 Saver You probably need to tap or hone the holes slightly. The XT60 connector may be stuck on due to adhesive. ...Enjoy!

**Please comment on here and let me know how it works out. It will help me improve and provide to this community. I put a lot of thought into these, even the miniscule details and i hope it reflects in my descriptions. My goal is to make things...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/4fUbLZLXOHl

Clean up your thicc build with this AS150 connector mount for + and - connections. ...Printed with ninjaflex tpu at 30% infill with good results.

So being the meticulous miniquad builder that I am, I was worried about the battery sliding forward and the cells or leads getting cut by the stack cover plate on the Ichabod Jr. So, I designed this 'Battery Bump Pad' as a gentle surface for the...

made a mount for the slammed squirt to hold caddx vista antenna, xt60 and immortal t style antenna or tubes i also added a remix of DroneCo's duct for 76mm props

I Designed a Rapid Solution to Securely Attach the Hoot Antenna and the Immortal T.

Insert stiffening agents into your packaging tubes to maintain their circular shape throughout shipping and storing procedures. ...Use a robust printing method, naturally.

Where to position this compact receiver while ensuring most of the antennas protrude from the frame? Upon considering that, I conceptualized the idea of not only having an antenna mount but also a mount for the R-XSR itself. 2 key points up front: ...

Printed in versatile TPU material, this innovative design serves a dual purpose - protecting arms and securing motors in place.

Shendones Squirt V2 VTX Receiver Antenna Mounts. When Utilizing Diversity Mounts, Recommend Using Antenna Tubes. ... Updated 09/04/2019: Version Added for TBS Unify Antenna with 3 Holes.

I crafted a custom battery strap mount for my Squirt v2's bottom plate, allowing me to securely attach my Osmo Pocket on top. The design leverages the 30.5x30.5 mm holes and cleverly fits over bolt heads situated in the 20x20 mm holes. Since I was...

I'd like to be able to print standoffs in the rear of my Ichabod Jr, as I'm not too fond of screwing into the TPU or using longer screws and adding nuts personally. Print with TPU (ideally Sainsmart TPU). Revision Note: This is no longer a work in...