shendrones shrieker 3d models

Mount a GoPro on your drone with ease using this sturdy reinforcement plate designed to withstand rigorous flight conditions. ...Print it out in durable PLA or hard plastic, and don't forget to upgrade those screws for added stability.

**Please comment on here and let me know how it works out. It will help me improve and provide to this community. I put a lot of thought into these, even the miniscule details and i hope it reflects in my descriptions. My goal is to make things...

Remix of Andy's DJI VTX antenna mount, it uses a MMCX Male to SMA Female Length: 80mm pigtail adapter. ...I purchased here: https://www.racedayquads.com/products/rdq-mmcx-pigtail-90-mmcx-to-sma-pigtail?_pos=1&_sid=a05bd3e5b&_ss=r I also used this...

Clean up your thicc build with this AS150 connector mount for + and - connections. ...Printed with ninjaflex tpu at 30% infill with good results.

Home made SMA mounting bracket connects to stand-off.

Tweaker 180 XT60 Saver You probably need to tap or hone the holes slightly. The XT60 connector may be stuck on due to adhesive. ...Enjoy!

Fabricated an interim top plate for my Tweaker as a temporary fix, pending replacement of the original.

Mount for 10mm diameter caps and the GPS Matek M10 5883 11/03/2023 Edit: -Added a version for a 16mm dimater Caps and Fettec Spike Absorvers

Remixed the original Siccario front and back shirts to be shorter to allow routing motor wires when braided or wrapped. Also including a version that is better compatible with the stand-alone DJI FPV heatsink mount. ... Original designs from...

I've found a way to keep my Tweaker XT60 Holder in pristine condition with its sleek LED design. A discreet hole on the backside allows for effortless cable management, keeping everything organized. To complete this setup, I recommend using Banggod's...

This is a custom-designed side panel cover for the Shen Drones Tweaker 180 quadcopter. Feature Set Easy snap-on design that eliminates the need for additional hardware Extends across the left or right stand-offs without interfering with the...

Proper protection for LiPos upon landing is crucial to prevent damage and ensure a successful landing procedure.

<p>This is a remix of the original design, printed with no supports in PETG&nbsp;</p>

This mount attaches a Gopro tab to the top of the krieger, requiring the low profile frame for the gopro session and shorter thumbscrew. Print Settings: Printer: Wanhao Duplicator i3 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2mm Infill: 20%...

That's a prime opportunity for mounting Foxeer Legend 1 cams on the Krieger. Flexible filament is highly advisable, as I didn't test this case with rigid filament, so it likely won't fit properly. ... Print Settings: Printer: TinyBoy Rafts: Yes ...

A top plate of 2-part was demanded to be crafted for the Tweaker system.

2015/10/01 Update Added Low Profile Mount Boosting the Tweaker 180 Mini Quadcopter Experience! Mobius and Dual Receiver Antenna Mount Are Here! Get a 20-Degree View with the Camera Enjoy the Thrill! Instructions for Maximum Fun: Customize Your...

Here is the camera's features. The 8MP image sensor captures sharp, detailed video in any lighting conditions. A wide 170-degree viewing angle and high-quality 14mm lens capture every moment. The PAL and NTSC modes let you record at up to 600TVL...

Thanks again for this remix!

Print with TPU

This is a remix of amfromch's lipo protection to extend the battery strap lifespan. Removed 1mm from the bottom layer to snugly fit the battery strap, adding 4 small feet for stability. Print cover at 1.0 scale PLA. Print feet between 1.0 and 1.1...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/4fUbLZLXOHl

The printer produced a high-quality print on the Thermal Processing Unit. ...My model showed significant improvement when using 40-denier Thermal Processing Unit material, 20 percent zigzag infill, and two-layer walls.

This mount improves on the stock Hydrophobe / Terraplane GoPro mount, giving you a more stable platform with less vibration. Angle is easily adjustable. This works with my improved skirt (coming soon), which can be printed with either an FPV mount...

I'm currently working on the Squirt V2, so I haven't tested or printed it yet! Designed this particular version because I'm building a new mount, inspired by Andy's recent design. ...I really like his work and have adapted it to fit a GoPro Session...

I crafted a custom battery strap mount for my Squirt v2's bottom plate, allowing me to securely attach my Osmo Pocket on top. The design leverages the 30.5x30.5 mm holes and cleverly fits over bolt heads situated in the 20x20 mm holes. Since I was...

Made to house a 4mm antenna tube, Radiomaster ELRS antenna, and the HGLRC tuning adapter usb extension. https://www.hglrc.com/products/hglrc-tuning-adapter-usb-transfer-extension-cable-module-for-flight-controller

TPU 90%+ infill, 0.20 resolution, Supports

With a dash of inspiration from the Xhover Airblaster frame and a nod to ShaggyFPV's request, I crafted these adjustable GoPro mounts. Grab some M5 lock nuts and M5 bolts or GoPro bolts, then position your camera in every conceivable angle. These...