shendrones mixuko 3d models

I've found a way to keep my Tweaker XT60 Holder in pristine condition with its sleek LED design. A discreet hole on the backside allows for effortless cable management, keeping everything organized. To complete this setup, I recommend using Banggod's...

Remix of Andy's DJI VTX antenna mount, it uses a MMCX Male to SMA Female Length: 80mm pigtail adapter. ...I purchased here: https://www.racedayquads.com/products/rdq-mmcx-pigtail-90-mmcx-to-sma-pigtail?_pos=1&_sid=a05bd3e5b&_ss=r I also used this...

A top plate of 2-part was demanded to be crafted for the Tweaker system.

Here is the camera's features. The 8MP image sensor captures sharp, detailed video in any lighting conditions. A wide 170-degree viewing angle and high-quality 14mm lens capture every moment. The PAL and NTSC modes let you record at up to 600TVL...

Home made SMA mounting bracket connects to stand-off.

Remixed the original Siccario front and back shirts to be shorter to allow routing motor wires when braided or wrapped. Also including a version that is better compatible with the stand-alone DJI FPV heatsink mount. ... Original designs from...

Front-end Mount for Squirt Servo with SG90 Servo. Required: (2) 10mm OD / 5mm ID bearings (1) 5mm Diameter shaft, 35-40mm long (1) Paper clip or piano wire to secure the servo and session together, with a small hole in the corner of the session. ...

This is a custom-designed side panel cover for the Shen Drones Tweaker 180 quadcopter. Feature Set Easy snap-on design that eliminates the need for additional hardware Extends across the left or right stand-offs without interfering with the...

made a mount for the slammed squirt to hold caddx vista antenna, xt60 and immortal t style antenna or tubes i also added a remix of DroneCo's duct for 76mm props

The TPU mount for the Osmo Pocket can be securely fastened to a Squirt, allowing it to freely hang in place. ...To achieve this stable setup, an M3 clamp is used in conjunction with several washers to ensure a firm hold.

Proper protection for LiPos upon landing is crucial to prevent damage and ensure a successful landing procedure.

This is a remix of amfromch's lipo protection to extend the battery strap lifespan. Removed 1mm from the bottom layer to snugly fit the battery strap, adding 4 small feet for stability. Print cover at 1.0 scale PLA. Print feet between 1.0 and 1.1...

A standoff of precisely 10 millimeters is established. The printed material, crafted from a PETG blend, boasts a robust 30 percent infill density coupled with the strength of five solid top layers and a swift, efficient honeycomb design. ...Resolution...

I Designed a Rapid Solution to Securely Attach the Hoot Antenna and the Immortal T.

This mount attaches a Gopro tab to the top of the krieger, requiring the low profile frame for the gopro session and shorter thumbscrew. Print Settings: Printer: Wanhao Duplicator i3 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2mm Infill: 20%...

Mount for 10mm diameter caps and the GPS Matek M10 5883 11/03/2023 Edit: -Added a version for a 16mm dimater Caps and Fettec Spike Absorvers

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/4fUbLZLXOHl

This is a remix of https://www.thingiverse.com/thing:4008135 but at time of posting, Thingiverse's remix feature doesn't work. The original wasn't compatible with GoPro thumb screws and required a 20mm m5 bolt. In this version, the m5 nut is...

That's a prime opportunity for mounting Foxeer Legend 1 cams on the Krieger. Flexible filament is highly advisable, as I didn't test this case with rigid filament, so it likely won't fit properly. ... Print Settings: Printer: TinyBoy Rafts: Yes ...

Print with TPU

Durable camera mounts designed specifically for Hero7 and Reelsteady Go cameras allow for effortless adjustments to capture the perfect shot. A battery strap thread passes through the rear piece, smoothly sliding back and forth to change the camera...

Print the base in a durable PETG or ABS material and the camera mount with servo in flexible TPU. ...The design requires a sturdy 10mm outside diameter / 5mm inside diameter bearing and a robust 5mm x 25mm standoff.

Nutmeg Spice for the DJI Air Unit - 3D Printed with TPU Material.

Here is a custom printed Damped Hero Mount designed specifically for use with ReelsteadyGo on the Hero7 camera. This innovative mount features arms that seamlessly slot into holes located at the back of the cam mount, allowing users to effortlessly...

This Hero 8 Rear Mount for the Geyser is engineered to secure itself to a customized antenna mount (supplied) using a coarse screw (I'm fairly certain it's a #10-32, but I've included an image of it)\r\nThe mount also wraps underneath and fastens...

So being the meticulous miniquad builder that I am, I was worried about the battery sliding forward and the cells or leads getting cut by the stack cover plate on the Ichabod Jr. So, I designed this 'Battery Bump Pad' as a gentle surface for the...

I'm currently working on the Squirt V2, so I haven't tested or printed it yet! Designed this particular version because I'm building a new mount, inspired by Andy's recent design. ...I really like his work and have adapted it to fit a GoPro Session...

I'd like to be able to print standoffs in the rear of my Ichabod Jr, as I'm not too fond of screwing into the TPU or using longer screws and adding nuts personally. Print with TPU (ideally Sainsmart TPU). Revision Note: This is no longer a work in...

I crafted a custom battery strap mount for my Squirt v2's bottom plate, allowing me to securely attach my Osmo Pocket on top. The design leverages the 30.5x30.5 mm holes and cleverly fits over bolt heads situated in the 20x20 mm holes. Since I was...

Print on TPU or Ninjaflex, featuring an opening under the arm for effortless escape mounting.