sharpie dimensions 3d models

I modeled this in Fusion 360 using a single revolve feature. ...Hopefully this helps you!

Customized version of http://www.thingiverse.com/thing:40406 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=40406

Supports are needed and have fun printing and using it!

Printed on an Ender 3 V2, Hatchbox purple PLA @ 219C. ...20% infill, no supports. 3-4 walls recommended to fortify marker holder.

Ironing on 0.10No supp

People printed the initial batch of holders, but they were too small, so they remade them to accommodate 35 units.

<p>Use a 6x2mm magnet</p><p>Print 100% infill</p><p>No supports needed</p>

Printed on an Ender 3 V2, Hatchbox purple PLA @ 219C. ...20% infill, no supports. 3-4 walls recommended to fortify marker holder.

This concept is currently being crafted, specifically for utilization within an extension located at https://www.thingiverse.com/thing:944952.

Customized version of http://www.thingiverse.com/thing:1147882 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1147882 Instructions Using the following options: angle = 20 holeHeight = 27 holeCount =...

Insert a 16mm x 5mm countersunk magnet, such as the one found at https://aussiemagnets.com.au/product/16-x-5mm-pot-with-3.5mm-countersunk-hole-rare-earth.html, into its designated receptacle.

<p>Print in vertical orientation, use supports for magnet slot.</p><p>8mm x 3mm circular Neodymium magnets are easy to find online or at hardware stores.</p>

Fine Line Art Markers And Cutting Blades

Hey Guys, Ryan's design is cool, but it's tough to quickly swap pens without cutting the cable tie and then messing around with replacing it. This design lets you easily tighten a bolt and use a variety of pen or marker thicknesses. No printing...

Customized Version of Thingiverse's "Wooden Puzzle Box" Created with Customizer! ...Thingiverse.com/Apps/Customizer/Run?Thing_ID=1147882 Instructions Using the Following Options: Base Height Set to 3 Units Angle of Rotation at 25...

Make sure the wand is oriented correctly so it uses less support, and I recommend using a raft as well, because there isn't much area on the bed. ... original: https://www.tinkercad.com/things/gEv5XcDctHb

A tiny marker cap that slips right onto a surface - no need for glue at all. ...Simply pop it onto a table or any other flat spot, and you're good to go.

<p>.2 height 20% gyroid infill no supports</p>

A makeshift solution was devised to accommodate uneven terrain by modifying the original design. A cone-shaped cavity was carefully excavated within the existing structure. ...This modification allowed the model to adapt to varied topographies.

A 1-piece Sharpier Marker Holder. ... No supports needed.

Customized version of http://www.thingiverse.com/thing:1147882 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1147882 Instructions Using the following settings: Hole Height: 20mm Gap between Holes: 1mm Wall...

Customized Version of Thingiverse Model 40406 Created with Customizer: www.thingiverse.com/apps/customizer/run?thing_id=40406 Instructions Using the Following Options: Spacing Set to 3 Units Height Set at 20 Units Tuning Parameters: a2 at -15, a1 at...

Make sure the wand is oriented correctly so it uses less support, and I recommend using a raft as well, because there isn't much area on the bed. ... original: https://www.tinkercad.com/things/gEv5XcDctHb

I can't fulfill that request.

This design is in the process of development, it is intended to be used in this add on https://www.thingiverse.com/thing:944952

I made this thing using Tinkercad, and you can edit it online at https://www.tinkercad.com/things/9JmYVKMdzrb. I created it to hold some new oil-based paint markers that I bought here: https://www.amazon.com/gp/product/B000GOYAPQ/. These are...