sharp by design 3d models

Please note that this flying stem is intended for general use with flier and skimmer miniatures, and not designed specifically for use with the Nautiloid. It is still serviceable in this capacity however. Using transparent filament for this model...

It is build to match the wled Board from Serg74, but you can use other controllers, too. The case has the following features:The "Stick" is rotatable 355° without the need to rotate the case itself.The rotation has snap points to reach exact...

Reszta drobnych elementów, przewody, złącza itd....XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXA complete Led lamp for a marine or freshwater aquarium, this is the whole design of the led lamp with electronics housing and led lamps for the lamp you also...

The rubber cover does need to be pushed in a bit more since it's designed to form a seal. Remove the button after checking it fits. 21. At this point if you wish to sand, fill and paint the model now would be the time to do it. I recommend using...

Simple bricks to play with or to integrate into other projects, designed to be easy to print, and easy to integrate in all other projects.Printing parameters:PLA//0.4 nozzle//0.2 layer height//0%infill//no support//brim All the parts in the files are...

The same design could be used for another type of water stopcock with a similar shape. For greater ease of use, it has been added the possibility of incorporating two slits to facilitate grip or to be used with a single finger. Print...

A tailor-made rendition of the design available at http://www.thingiverse.com/thing:58001 was produced using the customization tool found at http://www.thingiverse.com/apps/customizer/run?thing_id=58001[^] [#]мьий мастер-класс по созданию...

This is a small missile I built for use with a sci fy model. Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction...

I do not have a way to lift the rear of an XC90 however as I have not been able to design parts for that yet. Here are some examples of expected results: <b> Top hat spacers only; <b> Gain 1.75-2" of lift. Mine are 25mm, for example, the Cross...

The design of the MIK adapter plate does not allow this. <br>So I created a adapter plate that is MIK-compatible and at the same time allows Ortlieb bags to be attached.</p><p>If you are facing the same problem, then you have a solution here. <br>I...

This is an easy-to-print Synthesizer Stand for LYRA-8 Organismic SynthesizerWill support the LYRA-8 Organismic Synthesizer or Synthesizers around 266.7MM X 266.7MM or 10.5 inches x 10.5 inchesPlaces the Synth on a comfortable 5 degree slopeNo support...

I made a one with some modifications and designed this pen to use with it. I think the pictures are clear enough to assemble the pen. Here are some details: First of all,** BOM:** 6mm copper rod as main welding rods:...

If you have a printer, then you have such electronics! PaScn3D connection to Prusa 3D printer in a minute (tested!) – dedicated mounting brackets, components adapted to the dimensions of the device Modularity – adaptation to other printers without...

Made to transport your delicate machines while being carried on a starship across the far cold dark reaches of space.&nbsp;41mm X 41m x 30mmPrint at 0.15mmEnjoy!Designed on...

Get you Platform Walkways today and sleep safely knowing that heavily armed patrols will keep the alien mutant scum from crawling into your hab, slitting your throat, and taking what's yours!Shelter yourself! Deliver your cargo!Stay in the...

UPDATE: 20.04.2022adapterplate (new design) for model C&nbsp;Hello, we would like to introduce you to our stealthburner conversion mod.&nbsp;At this time it works only with the klipper Firmware.&nbsp;The use with “Marlin” is planned later and will be...

Not sure if you can see it since it won't list in the "My Designs" collection... Prologue I badly needed a replacement for my inductive Z-Probe because inductance and a magnetic bed don't go well together. So, quite a while, I was eyeing the...

Please note that this flying stem is intended for general use with flier and skimmer miniatures, and not designed specifically for use with the Nautiloid. It is still serviceable in this capacity however. Using transparent filament for this model...

# HEADS UP, I WILL BE TAKING MY MODELS DOWN SOON, THANKS TO THINGIVERSE TOMFOOLERY MESSING WITH LINKS, ETC ## Overview The idea behind this case is to be simple to print in terms of setup, required parts; and designed from scratch with 3d printing in...

When engaged in a full frontal attack, they are quite literally, unstoppable.The Original Galindos - https://www.printables.com/model/143724-galindos-robot-model-science-fiction Galindos Evolved -...

(Support Enforcers Only)Print 2 of the “Space-Port-Addon-Bridge-MOD-Wrecked-Support,” one of everything else.Resize for smaller or larger use.Clean your build plate with dish soap to ensure the floor of the Modules does not lift off (long...

To start, I altered the design from tin casing to a 3D printed enclosure for our DCDC-USB intelligent DC-DC converter with USB interface. To learn more about this product and its features, visit...

...It is loosely based on a Great Northern Railway Standard Frame Trestle design that I found on the web. I used a Prusa 3 to make this so some of these recommendations may not work quite the same with another printer, but I describe what I did here.

The "Horizontal" version is designed to print horizontally on the printer bed and prints quick and easy and only needs a small number of supports. The "Vertical + Carbon Rod" version prints vertically. This makes it weaker so I have left a 2mm hole...

&nbsp;These projects can be used as a starting point to slice other model combinations.&nbsp;Spout Lid (Experimental):This is a test design for a spout lid to pour out parts. &nbsp;I'm not sure the usefulness of it yet so I only modeled it for the...

Entry panels, hatches, and more!No support requiredDesigned on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

OverviewThe idea behind this case is to be simple to print in terms of setup, required parts; and designed from scratch with 3d printing in mind versus taking an existing sheet metal case and cloning it.I took inspiration for the assembly from the...

Ready to pump your promethium, sweet crude, or whatever lights up your day!Designed on Tinkercad.No supports required.Superglue the valve...

This piece is a straightforward, no-frills chair, designed for functionality and ease of use. It's perfect for those looking for a simple yet comfortable seating solution. Made with high-quality materials, this chair will provide you with years of...

Please note that this flying stem is intended for general use with flier and skimmer miniatures, and not designed specifically for use with the Nautiloid. It is still serviceable in this capacity however. Using transparent filament for this model...