sharkbyte vtx 3d models

This is a VTX holder / shelf for the TX5M.1 sharkbytre Prints with minimal supports needed!!

I didn't like how the sides covered part of the VTX so I cut the sides a lot lower so that I could plug in the firmware update wire easier and let the thing get better airflow. ...I also put in four holes so you can use m2 bolts to attach the VTX to the...

Dual mount for the TBS Immortal-T Antenna and a SharkByte VTX Antenna on the Catalyst Machine Works BangGod frame. I used the TrueRC Singularity MMCX. Mount slips over the rear standoffs. The Immortal-T slots into the mount before pressing the...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

I've added another version to secure the SharkByte Vtx onto a custom top plate of the SouthEastFPV Leventador Sport racing frame so it is exposed to the airflow during flight. ... You can find the custom top plate for the Leventador here:...

Externally accurate model of the Sharkbyte/hdzero vtx. ...25.5x25.5mm mounting, in a single body .step for your modeling convenience.

BetaFPV HX100 SE build - specifications: Frame - BetaFPV HX100 Flight controller - JHEMCU GHF411AIO F4 - (Previously I had used a Flywoo F745 but that is being used on another build and swapped for this more budget FC) VTX - SharkByte @ 25mw VTX...

sharkbyte vrx sma adapter, so you can replace the original patch antennas with better ones.

I mounted the CRSF in a [20mm flex TPU mount by Haku3D](https://www.thingiverse.com/thing:4731250) on top, with M2 screws through the side cage plate prints and into the VTX. You'll need 2 copies of the side cage plates with one being mirrored. ...

Sharkbyte mount for a cullmann tripod. Should also fit other tripods with 35x41 mm quicklock size. ... Base-plate should be printed as uploaded.

Created with Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=739573 **Instructions** Using the following options: lug_length: 5.0 font_catch_diacritical_sign_strategy: glyphs or bars bar_vertical_shift: 5.0 frame_thickness: 4.5...

This Pod is a remix from : https://www.thingiverse.com/thing:4516235/files The Canopy is optimized for Sharkbyte, printed in TPU. 5mm more in high. 3mm more lens protection. Made the front bigger for stiffness. Added a turtle mode fin with...

my own custom made pdb for more rugged power for powering the sharkbyte VRX and many goggles. can be powered from 3 till many S lipo battery's. ... stuff i used: polulu D36V50F9 step down converter 9V output https://www.pololu.com/product/4094 ...

I was getting fed up with not being able to switch my Sharkbyte unit on and off so I decided to mix these two items to create the power switch you see now. I printed it in TPU at 35% on my Creality CR10s. I used tree supports for the rectangular...

v1 files works. ... v2 female works great. use v1 Sharkbyte_2 as male. v3 final version works great. just use v3 files for this version. Enjoy removing the module whenever you need it! ...:)

***Update 1/22/22*** Added a stretched version of the fs_buddy design so stubby antenna can fit on the sharkbyte vrx and not interfere. ***Update 1/17/22*** Added file fs_buddyfor04xwcap. This file is the fan cap, with an fs buddy attached to it.

Press Fit Sharkbyte mounting to Skyzone 04x goggle fan... ...

You can find them on the original [Five33 switchback TPU mounts page](https://www.thingiverse.com/thing:3950022) The included mounts are below: 45° Foxeer Digisight mount with 1.7 lens 50° Foxeer Digisight mount with 1.7 lens Turtle mode arch...

You can find them on the original Five33 switchback TPU mounts page The included mounts are below: 45° Foxeer Digisight mount with 1.7 lens 50° Foxeer Digisight mount with 1.7 lens Turtle mode arch Seatbelt style mount for the rush cherry VTX antenna...

Here are the files for the SniperX Light 5 inch sharkbyte version Diffrence between analog is the top plate, called FATBOY

Today my Fatshark Sharkbyte fpv bundle arrived. Unfortunatly the fan-mount for the reveiver unit was missing so i had to print one by myself. I´ve testet the fan-mount on Fatshark Dominator HDO2 goggels and Fatshark Dominator HD3 goggels. ...Maybe it...

Adapter for the Sharkbyte TX5S.1 to a 20x20 M3 pattern. This has been remixed from https://www.thingiverse.com/thing:3314449 but for some reason thingiverse can't find it I simply thickened the base and removed the little poles. The thickened...

... holes with drill bit - did same with hex nut pockets with tweezers/razor. Hope this can help others similar to myself who love the HDZero system but have had issues with the provided Sharkbyte VRX cable - Happy to answer any questions. ...

- 25.5mm x 25.5mm mount pattern - Protects TX5S.1 VTX in a soft-mount cushion with lots of clearance between other parts to prevent short circuits or damage from contact in crashes - Protects digital camera, both Runcam HD and Foxeer Digisight...

There is an offset adapter for the stacked vtx, together with spacers to replace the stock threaded ones - you will need screws from 12mm to 15mm, and 4 screws to mount the adapter itself. For the 25mm vtx you need 8 screws from 4 to 6 mm. ... Feel...

Height as designed is for CRSF Nano RX to mount beneath the VTX and the VTX to be mounted with the RF board to the top - this results in much less than the recommended 10mm clearance so use at your own risk. CRSF Nano RX is mounted in a [20mm flex...

The entire process of creating this model is available on YouTube at https://www.youtube.com/watch?v=9KW7A50GOmg.

My entry for the VTX Cadathon