shapeways 3d models

I know, it's specifically for the Ender 3 & I am using a Mega Zero, so no surprise that it does not work but I have no idea why before now I didn't see the problem when using these Ender 3 designed mounts with my Mega Zero, even if I'd mirrored the...

This model was almost perfect, but when I printed one out, it turned out to be a bit chunkier than I really wanted. So, I figured I'd take my own shot at it and came up with this. My requirements were: * It had to match an authentic full-size...

I restarted from scratch and designed this model from those other inspirations. This version allows a 5015 fan to be installed without interference to the left or right gantry positions. I placed the fan above the slightly relocated CR Touch...

The diameter is 50mm, 23 teeth, pitch 2, height 20, slop .01.Updated threads were created using Fusion 360 and then incorporated into the Tinkercad models.  Several versions were tested at various tolerances to get just the right fit across...

I made a slight modification to the model by changing the profile of the USB input so the bridge was less than 5mm (was almost 10mm) and changed the way the board mounts so the top has all socket heads and no washers (just an aesthetic thing). <a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 custom_corner_resolution = 8 stencil_drawing =...

Update :Magnet Support Clip Hidden V2 - Added a slot for the 3rd magnet so now this piece with magnets can be used in the vertical orientation too.Parts to Print : All models have been printer at 200 microns, blade at 300 microns.Blood Splatter X...

Most issues with these printers can be traced back to this strain gauge probe not functioning properly.It would be convenient if their mainboards were compatible with the CR-touch / BL-touch probe style sensors found on the newest higher end Creality...

... find sellers on Amazon.com or Aliexpress.com. This is still a working project. I will update the bill of materials I used, add more models for RPi 3, and sensors when they are done. ...If you have any comments or suggestions, please let me know.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

I made this trap to prevent those pests from killing the bees in my garden if they ever come close. I collected information, examined several models, made by individuals and professionals. This is my version. If you feel it is inspired by something...

First off, thank you ohman74 for posting this fantastic Buster Sword What a great model to work with!! I wanted to make the materia in the sword light up and be replaceable. After searching for LED balls on Amazon I came up with this perfect...

I use washers between the skate bearing and the mount to give a little clearance for the spool holder to turn (I could probably model in a little bump out instead of using washers). For adjustable friction, I've added a simple bail that attaches...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protectionSuperior...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

The model is optimized for the connectors shown on the pictures. Super glue/cyano acrylate/any other transparent fast setting glue which adheres to your filament. Wire (should be thick enough for 700 mA and thin enough to fit into the carrier ...

Use at your own risk!!Check out the current version of this design here. This design is tested and ready for use, but only uses one blower, not two.</strong></p><h3>Basics</h3><p>This design stemmed from my desire to create a perfectly controlled and...

I hope this piece works for you; it was actually the most challenging to model and get right. 9. You should be good to reassemble now! 10. Put the hammer-trigger-piston assembly back in. 11. Lay the cylinder back in place, including the U-clip for...

[Medium Sized Model - 25mm base] [Presupported in 32mm and 75mm scale]   Usually mistaken as a courtier for her unassuming dress, Izumi often uses this to her advantage. Seldom is she expected to be as deadly as she is, and that underestimation is...

[Medium Sized Model - 25mm base] [Presupported in 32mm and 75mm scale]   The strong silent type of the Spirit Samurai. Kaoru is often thought of as the defacto leader of the group, despite being one of the youngest and much to the annoyance of...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protectionSuperior...

... list of Remixes. If I have missed something please advise me and I will correct this ASAP. If you do not want your Thing as part of this collection please advise me and I will remove it and try to include an alternate Thing for the missing model.

Each knuckle is 35mm in length, axis to axis. As of 09/16/2018, I've not yet modeled or printed the capstan bearings, nor have I fully solved how I will drive the capstan. My current thought is to use a drill attached to the underside of the...