shapes 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 height = 15 shape =...

Then, the spring structure is “pinched” on the top to make a cone-shaped spring. Next, the contour of the spring body projected onto the sketch. Finally, a sweep function is performed to create a flat spring. It’s easier said than done as Fusion 360...

I am NOT a designer or engineer, simply a hobby enthusiast who dabbles in upgrades.Idler Door/Lever from https://www.thingiverse.com/thing:3652205 (MMU2S) OR https://www.thingiverse.com/thing:3469271 (MK3S)Sensor/extruder lid from...

Press-fit six pin receptacles into the W-shaped mounting bracket (into the holes that go all the way through). The recommended pin receptacle will sit flush with the top surface of the mounting hole when fully inserted. As designed, it will take a...

To fix this, I cut the shape of the rotation lock collar into the bottom of the assembly so that it slides all the way down and friction fits over the whole collar. This was much more stable and allowed the motor to turn smoothly. I'd like to...

(Towards outer/inner edge of the blades) - How is the shape of the curved blades determined? Are they just drawn how they look good? How do i know the blades dont only look good for me, but for the water? - How many blades should the impeller have?...

SETUP If necessary, charge the battery (check it by pressing the button on top and peering through the battery-shaped hole in the front. Four lights = fully charged). Connect the HDMI port to an HDMI monitor, and the USB ports to a keyboard and...

The adjustable L-shape mounting bracket provides support for the opposite end of the fixture.Suggested Applications:Paint spray booths, aircraft maintenance, oil drilling rigs, refineries, solvent and cleaning areas, chemical manufacturing, waste...

30-pin flat cable from left to right, all seen from the flatcable connector end of the L-shaped middle circuit board. |Z-axis flat cable pin|X axis flat cable pin|Connects to|Additional info| |---|---|---|---| |1| 1-4| Heat block +24V |...

Cosmetic inserts for coloring the positive symbol (called positivemarker.stl)2x_negative_terminal.stl and 2x_positive_terminal.stl are both minor tweaks that work with the captive nut system.2x_door_final.stl is a slight shape change to allow more...

The whole mount is now a complicated cone shape (ish), and the front (v2) is rounded off. ##### Update 18: Printed version 21 and the corresponding front! It printed fine; although since it was cold outside, I used a brim, and there was a bit...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 height = 15 mirror = Yes shape =...

I realized that the smaller inner diameter of this tube helps to shape an nice thin tip after retraction from the melting zone. The proper inner diameter seems to be 1.85 mm as discussed <a...

Cut, fit and try again till you like the shape of the bend in the tube. With the whole trigger assembly in place, you can mount the grenade launcher. The exact placement is not critical, just make sure there is enough room behind it to comfortably...

Identify the point where this line intersects with the vertical center line.Make another reference line 4.13cm up from the bottom of the box.Make a vertical reference line 0.7cm from the right side of the constraint box (the line should be between...

They need to print twice.May scale up 2x the nose clamp at Z if it couldn't hold the shape well.Facepiece 0.5mm thickness. It must be Z0.2 initial layer and Z0.1 layer height, total 4 layers.</p><p>Disc must be Z0.2 initial layer and Z0.1 layer...

Bend the thermistor leads in L shape so that when the rest is flush to the cork backing’s surface, the thermistor pushes against the print bed and its back protrudes 1mm or so above the cork backing’s surface. You might plug the rest of the...

------------------------------------ ENGLISH ---------------------------------------------The guide was translated using google, I apologize in advance for any errorsTo conclude the set of linear guides on the X1, this time I propose some attachments...

The vertical version needs lots of supports and has a + shape at the top which is removed after printing. I found that the vertical version runs more true as there is very little warping.</p> <p><strong>You can also find some experimental parts...

Some of angels said that when he open his wings he cover the sky , some of them punished some people by carring their village on the edge of his wing and droped it , some screamed at them so their guts were teared away , they are so powerful with...

So the measuring cup has a unique, conic shape. Also I was very keen on trying transparent material, so I really had a lot of fun with this project and extended my knowledge and experience with 3D printing quite a lot.This design is not for the faint...

I'm also currently studying to be a mechanical engineer so that comes with its perks too i guess, mostly in the shape of Siemens NX which is another can of worms to learn again :DI do look forward to your makes and any questions you might have about...

SETUP If necessary, charge the battery (check it by pressing the button on top and peering through the battery-shaped hole in the front. Four lights = fully charged). Connect the HDMI port to an HDMI monitor, and the USB ports to a keyboard and...

...&nbsp;You start by making a pentagon shape from 5 AAB facets.&nbsp;Slide 2 wedges on to one A side of an AAB facet &nbsp;&nbsp;Then slide on another facet by its A side - ensuring that the B side is on the same outer edge as the first facets B side.

So I gave a demonstration of how it worked and showed a few diamond shaped stones I had made out of glass marbles with it. The initial reactions were like wow, but then I had really weird interactions like one lady she was like almost screaming at...

I've included the boards the moulds are modelled on, so I'd recommend printing those out first and seeing if you find their shape, size, and wheel base to your liking before deciding to print the moulds and shapers. There are two boards, one of a...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes shape =...

Make the necessary adjustments, if this is not the case.Push the speed controller knob on its shaft (decide yourself what the off position should be)Put the wedge shaped case against the inner disc and check that the small bevel gear is aligned with...

The adjustable L-shape mounting bracket provides support for the opposite end of the fixture.Suggested Applications:Paint spray booths, aircraft maintenance, oil drilling rigs, refineries, solvent and cleaning areas, chemical manufacturing, waste...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = .8 height = 15 mirror = Yes shape =...