shapeoko xxl 3d model

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...

Since the build volume on the Prusas is relatively limited i decided to maximize the footprint of the stand for stability. As for the height, the 2 piece construction while theoretically takes more time to print, there is no need for support for the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

It's worth the trouble to get access to a laser cutter to get cut panels.  The duct is intended to print at a 45 degree angle - the part model is oriented as it is intended to be printed. The duct part DOES NOT NEED SUPPORT. Your slicer may...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

Able to hold 1 stack of cards and 2 columns of hexes. --4-2-17-- Added player card 2.2, a little bit smaller on the separator pieces that come off the model, should be easier to fit in the box. --4-2-17-- Removed older hex and cards .stls and...

The stock globe has a vent on the top and there are vents in the model to aid the convection cooling. Is it *really* needed, especially with the converter gone? Dunno so the optional rain cap comes with the caveat of possibly shortening diode...

Four screws for every corner and 8 screws for every side.[blue] NO acrylic glass holder at the side where the hinge mechanisms are located!From this on the “Front” is where the hinges are.[green] At the location of the green circle you can drill a...

You may have to do some light cleanup, but the fit of the parts should be snug enough to hand press together with no wobble. IOMarms STL- These arms are taken directly from the original wood designs and are generally sized for an IOM, but are not for...

We are modelling the *BELT* tooth here, not the tooth on the pulley. Increasing the number will *decrease* the pulley tooth size. Increasing the tooth width will also scale proportionately the tooth depth, to maintain the shape of the tooth, and...

Or rather, it's a scale model of what that house looked like fifteen or twenty years ago. The wrecked version is closer to how it looks now that it's been abandoned for the better part of two decades. The tweakers have had a field day with this...

The use of simple metal parts in combination with printed components holds a lot of potential for the future; FreeMenDontAsk is already working on other handgun models. Even outside of gun making, this could be useful for a wide array of printed...

rice or sand.Glue if the press fits are not tight enough Testing tolerancesStart by printing the models press_tolerance_test and rotation_tolerance_test from the folder Common parts.Press fit toleranceUse the press fit test to decide which press...

The design is a complete rework of my older oscillating fan model.It uses a common 130 size brushed hobby motor and incorporates an 18650 battery in its base for completely portable operation. Compared to the older design, the new version has...

It deviates a bit of what I usually call an "sci-fi astronomical object", because it's an in-spacecraft transport vehicle. I made this model available in 4 scales. I left the model in "halves" that I consider the best way to print it, of course, with...

Model says 119mm, which would be close.???---------------------------------------------------------------------------------------------------------Printed Parts: Base:___________________Placeholder____________________This is the base of the...

If do you need to get the lock back off, the best way I found was to stick long allen keys into both of the lock's holes and then pinch them together to lever the lock slightly apart, which reduces the pressure enough that you can wedge a thin...

I illuminate my RepRap 3D printer's control panel with it. The LEDs require a 12-volt power supply which can be supplied by the printer electronics (Rumba Board). Material: ABS, 3mm thick Nozzle: arcol.hu hotend v4.1.1, 0.35mm diameter Printer: DIY...

The servo spindle should be towards the middle of the robot.COGCut the servo horn with a pair of wire cutters so that it fits into the cogPush the servo Horn onto the cogMake sure the servo is at the minimum rotation position (turn it clockwise until...

Remove the z-axis tops and replace with this light bar mount. Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill: 15% GyroidSupports: Build plate onlyOpen 3MF files in PrusaSlicer for preconfigured settingsRequired...

It appears to be a set of points in 3D space represented using an [Hull format](https://docs.python.org/3/library/pickle.html#pickling-hints). I will assume you'd like me to convert this into some kind of array. However, there are no "lines" or...

I've spent quite a bit of time getting to this design and I want to make it as accessible as possible so that as many people as possible can enjoy the greatness that is easy loading/unloading of the MMU. Good luck and enjoy!! Print Settings Printer...

Remove the stock z-axis tops and replace with this light bar mount.Dual Mount Z-Axis Top No Switch: Same as Dual Mount Z-Axis Top with no hole for the power switch.  Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill:...

These strips are bright enough I didn't notice only one was on. View from Octoprint Control tab during the first layer of my first print after installing. Print instructionsCategory: 3D Printer Accessories Summary Prusa i3 MK3 PiCam v2 X-Axis Motor...

Use with Right MMU2 Mount Z-Axis Top. Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill: 15% GyroidSupports: Build plate onlyOpen 3MF files in PrusaSlicer for preconfigured settingsRequired hardware:Aluminum u-channel24V...

Remove the stock z-axis tops and replace with this light bar mount.Single Mount Z-Axis Top No Switch: Same as Single Mount Z-Axis Top with no hole for the power switch. Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill: 15%...

By doing so, I can now get more of the STLs to show up in 3D view on this site. The updated files have 10-18-23 dates and are renamed with "-remake" or "-k". 10-10-23 Update: Two items - Assembly Hints and Images added as a new section, and an...

I'm not telling you how to 3D print parts and clean it. You know it. BOM: '1. RPi 3A+ / Zero W /Zero W2 (and similar clones that have the same outline as Zero), microSD card, '2. Raspberry PICO working as keyboard martix USB HID device...

... at 0.2 layer height.</p> <p>But once you've raised the limits, it's worth seeing what a 350mm/s travel move really looks like at 5500 or 6000 mm/s^2. (Answer: sorta scary, honestly) Designed from scratch in SketchUp. Category: 3D Printer Accessories