setting z offset ender 3 3d models

When i bought the Ender 3 i also bought a glass bed from creality to print PLA. Recently i started to print with PETG. And the original bed is better for PTEG. But without autoLeveling is very difficult to change the bed's between materials. So i...

A key for manual control of the z-axis lead screw on your Ender 3, also compatible with CR10 printers and others using T8 lead screws with 4 start threads and an 8.0mm pitch or 2mm per thread. I redesigned this from the...

This is a fairly simple belt driven z mod for the ender 3, pro, v2. I haven't tested it on any printer. I would advise printing the parts before buying anything just to make sure it fits. BOM 1x6mm od aluminum tube at least 100mm overall.(1x50mm...

My new Ender-3 arrived today, and the nut for the Z lead screw rod is missing threads as if it was not tapped. It should be T8 trapezoidal threads with 2mm pitch; if that's true, this should work (amusing my first try at Fusion 360 was done...

Required parts: - An M5 tap and die set for the top V-slot profile's two edges - Six M5x30 screws - Two M5x25 screws - Four M5x10 screws - Ten M5 T-nuts - Twelve M5 washers - Two M10 acorn nuts - Six M10 nuts - Eight M10 washers - One meter of M10...

This design has been tested for the Creality Ender 3.\r\nAll you need to get started is a fastener - no screws or nuts are required!\r\n\r\nYour thoughts and suggestions are welcome, just leave a comment below.\r\n\r\n**Check out my...

And the original bed is better for PTEG.But without autoLeveling is very difficult to change the bed's between materials.So i found a design to adjust the Z EndStop and add spacer ability to quick change the bed's.I used the EndStopCover to develop...

Hardware: 4 - M3x10mm screws 3 - M4x8mm screws 3 - M4 T-nuts Helpful Tips: ALL filament shrinks after cooling. The amount of shrinkage depends on the type of filament. PLA shrinks about 0.25% PetG shrinks around 0.35% Taulman 910 shrinks 0.31% That...

Ender 3 Z-motor Clamp ===================== Why I Designed This ------------------- The Ender 3's motormount, located on a single top edge of the Z-motor, often results in the motor being tilted away at the bottom. This causes the motor axle and...

Remix of Ender 3 mount, the original was fouling with X gantry on my setup. ...so remixed a bit slimmer one, still works with T-Nuts.

Z endstop mount

The Optic Endstop is a crucial component on the Zender 3 that helps maintain precise control over the printer's movement, particularly when it comes to the Z-axis. ...This device is tasked with detecting the physical limit of the Z-axis, thereby...

I recently printed someone's Z axis adjustment parts for the Ender 3, and noticed some issues I had with it, so I design my own. My design has some nice features, like the X axis cover uses 2 of the original screws to hold it in place, and the mount...

This is a remix of thing:2725795. ...I didn't have a 3 x 30 mm screw so I remixed it for a 4 x 30mm. ...I also added a thumb screw so I could lock the Z stop.

Wiring: So far, I've only tested wiring a second stepper in parallel with the original stepper, increasing current to 1 amp (Skr 1.3 with 2208). Also, my second stepper is different from the original Creality stepper, which isn't recommended. I'll...

I remixed mlynch002 because I wanted my in the original location and so my ender would fit better on my desk after the dual Z screw was added. Would highly recommend the dual z, and my remix of his design uses about half the filament / print time,...

I remixed mlynch002's design because I wanted my printer in the original location, so my ender would fit better on my desk after adding the dual Z screw. I highly recommend the dual Z upgrade, and my remix uses about half the filament and print time...

I modified the bracket from the original design here: https://www.thingiverse.com/thing:2757810 to fit the Ender-3 printer by shortening it in Blender using the STL file. To assemble, you'll need to print nine link_top.stl parts and nine...

Adjustable end stop for the Z axis.

This is a remix using tinkercad.com to remove a 30x3 mm section to wrap around the x-axis belt tensioner on my Ender 3 v2. The tensioner sticks out so the part that takes the place of the spacers can not lay flat without removing some of the part. ... ...

Parts: KLF08 Bearings: https://de.aliexpress.com/item/32793159224.html Ender 3 Rod: https://de.aliexpress.com/item/32904246004.html GT2 Timing Pulley: https://de.aliexpress.com/item/33017482340.html GT2 Belt Joining:...

Replacement for Creality part. ...Allows adjustment of z-screw position.

To examine the calibration of the bed plate along the Z-axis; To inspect Z leveling on heated surface

To verify the calibration of the Z-axis on the heated bed; Verify z-level on hotbed

The human shields the filament from damage caused by a collision with the z-axis rod.

Reminder for the movement of the Nozzle up or down (Z-Axis)

The Z-axis Test 1 utilizes materials from the Model LM8UU.

This design was printed with these settings for myself with Prusa Slic3r. ... Infill : 30% Resolution : 0.2mm Supports : Bridging Material : ABS Wall : 3 2021-12-01 - Printing in progress.

The knob is designated for use with the Ender3/ender3 pro z-axis print model. ...It features a prominent label with the letter "Z" clearly printed at the top.

The spiral shape is getting a slight upgrade to fit on the Z knob. ...This updated design is also slightly thicker, which should allow it to clear out most of those pesky z-axis stabilizers.