sennheiser md421 mic clip 3d models
110437 3d models found related to sennheiser md421 mic clip.
prusaprinters
The original "ring" on the mic of my FTM-400 XDE was not really useful for hanging the mic anywhere - so I made a new one. ...I should work with other Yaesu microphones as well, let me know if you made it work with your transceiver!
thingiverse
Use cable ties to secure the clamp on the mic stand. One should suffice, but you can also use two if needed. I opted for the larger ones. The mic-stand diameter is 15mm. This setup works just as well with a larger diameter, up to 20mm. Have fun...
thingiverse
I'm really fond of the little mic that comes with the Baofeng UV-5R radio. If you're like me and considering mounting a radio in your vehicle, this is an easy and affordable way to test the waters. You'll likely experience reduced reception if the...
thingiverse
Replace the worn-out XLR cable clips with new ones featuring a 10mm square profile to ensure secure connections. ... Discard any damaged or frayed hook cables to maintain top-notch audio quality.
myminifactory
Replace old worn-out hook cables with new ones; use a sturdy XLR cable clip to securely fasten 10mm square profile pantographs. ...Get rid of any damaged or frayed hook cables.
thingiverse
Microphone clip for Nolan N-Com. The redesign has a thicker base with a deeper clamp grove and a few additional fillets for a better fit. An M4 screw is needed for assembly. ... *Print thin layers and 100% infill for better endurance.*
thingiverse
... against accidental turning on, as well as making sure all the shiny top faces are against a pouch soft wall, and the cables are on the other side. So this is a clip-on frame to keep your senders and the receiver fixed and somewhat more protected.
thingiverse
What: A self clip design for the Sony ECM-XM1, allowing the microphone to securely attach to its XLR shell/plug. Why? I created a remix that enabled the microphone to be attached to a shoe mount. ...Although it functions well, I often shoot with a...
thingiverse
This model was created using Tinkercad's powerful design tool. ...You can easily edit it online at https://www.tinkercad.com/things/kYuWkie6zv7
thingiverse
This video is designed for those who need to set up two microphones on their snare drum, as this model accommodates the "Shure SM 57" and "AKG P170" microphone. ... Material: PLA Layer Height: 0.1mm Infill Density: 25% Raft Requirements: Not Applicable...
thingiverse
I'm attaching this small device to my microphone stand. ...Its primary function will be to organize cables, but it will also serve as a resting place for my headphones when not in use.
thingiverse
Used to secure a device to a base for stability and support.
thingiverse
Clips for Mic Arms Short version inner height: 15mm x 10mm Long version inner height: 19mm x 10mm
thingiverse
I was worried about ruining the antennas on my Sennheiser G4 lavalier mic packs so I decided to design a cradle to keep them upright.
thingiverse
I designed these based off of some clips that came with my mic stand that broke fairly quickly. ...The top layer cracked when testing the clips, but it seems to still be holding up and I may change the design to prevent that from happening.
thingiverse
Obtained a new Lavalier Microphone for my job; unfortunately, it broke right away. Fortunately, I have a Makerbot on my desk, which came in handy. The next morning, I noticed the microphone sitting next to a wire tie and had an idea! It can be used...
thingiverse
Sennheiser Microphone Holder Mounts Securely onto Various Sennheiser Microphones.
thingiverse
Sennheiser Replacement Earbuds Designed Specifically for Sennheiser IE 8 Headphones
prusaprinters
A tray that holds 5 Sennheiser e904 microphones so that they take up minimal space in the case drawer without flying around. It features a space for 19mm spike tape for labeling as well as slots to easily grab the mics.
thingiverse
Replacement Headband for Sennheiser Urbanite XL Headphones.
thingiverse
... for attaching a 3mm wire to the square 10mm stand. Printer Settings Printer Brand: Printer: Prusa i3 A8 Rafts: No Supports: No Resolution: 100 Infill: 100 Notes: With print times of just a few minutes, it's easy to produce multiple clips at once.
thingiverse
I needed some extra clips for my microphone-to-headphone cables, so I spent 5 minutes designing and 30 minutes printing them out to reduce clutter. The fit is spot on with my setup, resulting in a snug hold that requires just a gentle push to click...