seemecnc rostock max v2 manual 3d models

Custom Mount for E3D Titan Extruder on Rostock Max v2 This is a custom mount designed specifically to install the E3D Titan extruder on the Rostock Max v2. If you'd like to show your appreciation for this design, please consider making a donation of...

I've simplified this model to suit the needs of E3D enthusiasts using the Flex3Drive extruder on their stock Rostock Max V2 platforms. ...This design enables a straightforward mount for both the E3D v6 and its attached fan.

If you'd like to support this design, please donate some money here: https://pinshape.com/items/21183-3d-printed-e3d-titan-extruder-mount-for-rostock-max-v2 Update: 4/22/2016 The bottom was shortened a little so the bottom edge no longer sticks out...

... support from the original Rostock mount along with two plastic nut holders from Alexstoff's dual ezstruder mount which is found at http://www.thingiverse.com/thing:364325. Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No

Mounting bracket for using geared extruder (Namely this one: http://www.thingiverse.com/thing:18379/) on Rostock Max v2. Original EZStruder had problems with lost steps at high extrusion rates. I also added modified 5mm longer guidler because...

Here's the spun version: This revised mount, tailored specifically for my Rostock Max V2, draws heavily from the original Reprap Discount Full Graphics Mount design. ...However, a critical modification was required: switching to Marlin firmware instead...

Included in this manual are essential files necessary for successful operation: Marlin Configuration file: This file contains settings tailored to optimize performance on the Rostock Nano. Repetier Host print filament setting INI file: A crucial...

Print Settings: Printer Brand: SeeMeCNC Printer: ORION Delta 3D Printer Notes: You may need to scale up to get your camera to fit. I used a rubber band to secure my camera to the mount, which has an OD of 6mm. To get the best results, orient the...

A couple of things aren't lined up correctly...\nFirst draft of my OctoPanel design for the Rostock Max V2. This panel replaces the left side lower panel, which in a stock Rostock Max V2 is simply a piece of ~100x~200mm melamine.\nThis panel...

The Rostock Max V2 just got a major boost with the upgrade from the standard fan shroud to an E3D V6. To install this sleek new shroud, simply swap out your current fan and slide it into its new home, then press it firmly into place. ...The existing...

Effector mount that allows you to run any Rostock Max V2/V3 hotend and corresponding mounting solution including the E3D V6 and clones, or the HE280. I measured the mounting holes in the stock effector on the Kossel Clear magball effector and my...

The Rostock MAX v2 layer fan shroud/duct is specifically designed for a 5051 blower fan. Initially, this design was intended for the older effector platform featuring universal joints and an old PEEK hotend. However, I can now use the fan up to...

The video at https://youtu.be/FPhVwWSVVz0 demonstrates an effector mount designed for use with Rostock Max V2/V3 hotends, as well as their corresponding mounting solutions such as the E3D V6 and clones, or the HE280. To achieve this design, I...

These arms are 150mm long on center, matching the same spacing as the Rostock Max V2 bolt holes, so they should fit nicely together underneath the bed and provide a clear guide for the screws attaching the bed to the base to go through. ... They're...

Print Settings: Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: No Notes: ABS is recommended because PLA may be at risk of melting. Post-Printing: Depending on your printer's calibration, you might have to drill out the paths where...

Print Settings: Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: No Resolution: 0.2mm Infill: 80% Notes: I used ProtoPasta Carbon Fiber, a PLA material that will be interesting to see if it holds up and doesn't deform. It's...

I struggled for hours trying to print ninjaflex on my rostock max v2, even with the filament support mods people suggested, I still had no luck. Having designed this extruder myself, it hasn't given me any trouble with printing soft or normal...

Since the Duetwifi is too big to fit inside the Rostock Max V2 base, I adjusted the panel so you can wedge the Duet partially in the base, with the rest outside my Paneldue adaptation. I had it protruding just enough to allow inserting an SD card...

I'm turning my Rostock Max V2 into a super speed printer, which means I need some serious part cooling. I've got a Berd-Air up top but sometimes need some extra air, so I added a couple fans beside the bed. Just use normal PC 80mm fans. You can hook...

... need an extension for your dial indicator. This particular design is tailored to work seamlessly with 3/8-inch barrels found on most dial indicators. You will require two #6-32x2in screws to secure this mount firmly onto your Rostock MAX printer.

This is an upgraded rendition of Excelcier's Rostock Max Replacement Spool Arm, tailored for wider spools. All I did was smooth out the edges to minimize friction when the spool tries to rotate on the arm. **Important Note:** If you downloaded the...

... out the RAMBO board for a Duet 2 WiFi, upgrade with ease by adapting the existing board mount. ...Use Seemecnc's file as a starting point and make adjustments to accommodate the new Duet holes, relocating the fan to a central position in the process.

I also designed it to work with just about any Hotend Mount for the Max V2, including the stock mount. If you search for my Bltouch mount for the Max V2, I designed it to be compatible with the setup linked in the description. I was surprised at how...

Dual-Extruder Upgrade Spool Holder Made Easy with SeeMeCNC Panels This project uses standard US hardware, featuring 1/4" threaded rods and 1/20 nuts, because sourcing metric parts in America can be a challenge. If you're not particular about using...

I couldn't find a shroud that fit my 40x40x20 blower fan, so I modified the standard shroud using the STL provided by SeeMeCNC. I designed it for a snug interference fit between the fan and shroud, which may require light sanding to get a perfect...

I designed these clamps for the RoMax V2 based on its stock machine profile, including a 10mm bottom mounting plate heater plate clearance, 7mm of bed clearance that accommodates BuildTak on top of glass, and a beveled curved edge to match the 310mm...

I designed these bed clamps for the RoMax V2 based on the stock machine profile, including the 10mm bottom mounting plate --> heater plate clearance, 7mm of bed clearance that accommodates BuildTak on top of glass, and a beveled/curved edge to...

Print Settings: Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: No Infill: 30% Notes: Printed on Rostock Max V3 with PLA How I Designed This: Remixed from http://www.thingiverse.com/thing:1664735, this design has been enhanced with...

I suggest printing:\n1 shell\ngo without infill\nto minimize weight.\nthere's no need for screws,\nas functionality is all that matters.. ...\nThis 3D object originated from http://repables.com/r/212/\n\n \n \n ...

It's a versatile sleeve that easily snaps into the 1" opening where hot end, extruder, and layer fan wires are routed through. The heat shrink tubing provided with the kit didn't quite shrink enough to stay securely above the hole, so it has slipped...