seemecnc rostock max v2 manual 3d models

This is a key base platform for Rostock Max V2 with built-in layers blowing air directly to hot objects during print run phases.

Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX v2 Rafts: No Supports: No Resolution: .2mm layer with .5 nozzle Infill: Doesn't matter Notes: Printed in Microcenter Inland ABS at 240 with the bed at 90 on glue stick. I use a Prometheus...

I lost the original links long ago but am posting these here in case anyone else needs them. ... They are the mounts for an E3D V6 hotend onto the Rostock Max V2/V3 platter.

This thing is a idler adjuster for SeeMeCNC Rostock Max v2, makes tightening the belts easier on this printer. Note: This may fit SeeMeCNC v1 and Orion printers too! Tightening the belts with the adjuster means no pressure on pulley or mangling...

Here is a nimble mount specifically designed for the Rostock Max V2 by SeeMeCNC featuring the PEEK Hotend. Visit https://www.thingiverse.com/thing:2184991 to access firmware settings. To print this model, rotate it with supports or skip them if...

Print Settings: Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: No Resolution: .2 Infill: 20% Notes: Print in a horizontal direction so that the layers are lined up for greatest strength. Two small areas of bridging, but these...

You'll need just a few basic components to adjust the belt tension on your Rostock Max V2, and don't worry, they won't require any major modifications to the setup. ...A longer set of 6/32 machine screws is all you're going to need here, luckily I was...

I crafted this mod for my original Rostock Max V2 heatbreak layer fan mount, using it straight from the box. ...After switching to an E3D hotend, I flipped the factory-standard fan mount upside-down to accommodate LED light installations and that made...

This creation is designed to link the hotend from seemecnc to a Rostock base.

... become the primary intake vents. Nothing in the base (RAMBo, SSR, 12V buck, PSU) gets over 35C even after hours of continuous printing. Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: No Resolution: 0.2 Infill: 15%

A Quick Caliper Mount for Rostock Max V2 Calibration I threw together a makeshift caliper mount to calibrate my Rostock Max V2, and it works by screwing on just like the standard hotend top plate. To reset the caliper when probing, use a rubber band....

It's a mounting bracket designed to hold a dimmer and a 0.28-volt meter securely onto the Rostock max V2's melamine lid. The main purpose is to control a 15-LED angel light ring surrounding the hot end and include a volt meter as an added feature.

This mount is specifically designed for a Go-Pro style camera that seamlessly fits on a Rostock Max V2 setup. One of the spacers located below the bed and two screws are used for secure mounting purposes. The primary intention behind creating this...

Either way, here's a low-cost solution I came up with (literally) for your SeeMeCNC Rostock Max. The brackets snap on and the shield sits in the groove. I didn't use any adhesive so I can remove the shields easily. If the effector bumps against the...

Also, the Rostock Max v2 is designed in English units only - not metric. Instructions Print two identical spool holder assemblies - one for inside use and one for outside use. Enable supports so bearing holes print clearly. ... To...

It's a mounting platform designed specifically for use with a 60mm 15-LED Angel Eye Light around the Rostock Max v2 hotend. This platform securely snaps onto the hotend in three distinct places, effectively holding the LEDs firmly in position. A new...

It's a bracket that secures a dimmer and a .28" volt meter onto the Rostock max V2's melamine lid. The purpose is to control a 15 LED angel light ring around the hot end, allowing for adjustable brightness and enabling users to turn off the lights...

It's a mounting system for utilizing a 60mm, 15-LED angel eye ring on top of the Rostock Max v2 hotend. It snaps securely into place by clipping onto three distinct points to firmly hold the LEDs in position. Unfortunately, this light mount is not...

The bracket attaches to the top base plate on the Rostock Max using two M3x20mm screws after you drill clearance holes in the top plate for them. ...This setup enables users to see their machine's voltage and utilize an auxiliary power source on a...

... a badge for my Rostock using an old-timey font. ...I scaled mine up slightly, but the standard size should fit perfectly on a Rostock Max body panel. ...It's highly recommended to be extremely gentle when printing this design and use plenty of cooling!

... Got bored in Inkscape today and made a badge for my Rostock in one of them there ole timey fonts. ...Scaled mine up a little bit, but the default size should fit on a Rostock Max body panel. ...Recommend being very gentle and use a lot of cooling!

A customizable side panel designed specifically for the SeeMeCNC Rostock Max V2, accommodating a 92mm fan installation to enhance air circulation around the machine's internal components.

Pen/tool holder for Rostock MAX v2

The stock spool holder support serves as an integral component of the RoStock MAX V2 developed by SeeMeCNC, providing essential support for the Dual Spool Tower mod found at http://www.thingiverse.com/thing:746717 . ...This STL model was crafted based...

Support for ventilator for Rostock Max V2 3D printer

Works optimally when printed using a high-strength nylon-based filament material.

This is designed by Michael Hackney. ... You can refer to the original text here: http://www.sublimelayers.com/2016/10/installing-bondtech-qr-extruder-on-my.html Bondtech QR extruder is available for purchase from its manufacturer at...

... maybe a pen/plotter mount or drag knife mount? A laser mount could be really cool too! This design is inspired by DougLorenz's lowrider mount. Print Settings: Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: No Infill: 55% or better

... It. Printer Settings: Brand: SeeMeCNC Printer: Rostock MAX Rafts: Not Required Supports: No Need for Those Resolution: Any Desired Level Infill: Choose Your Preferred Density Notes: Print Standing on Edge, Thicker Side Down, and You're Good to Go!

You can create something to attach to the tabs on your SeeMeCNC Rostock Max v2 effector if you want. There are three of these tabs positioned at 120 degree angles on the effector. Simply transform this model into a hole in TinkerCAD and then slide it...