seemecnc h2 3d models

This one was modeled purely off the included drawing in the H2 manual and the actual fans to be mounted. There's also a version for a 4020 fan size (shown in the photos). This is the one I've been using, as it's a lower profile than the 5015 and...

Remixed from: https://www.printables.com/cs/model/115518-biqu-h2-ender-3-v2-mounting-plate-with-bltouch Intended to be used with: https://www.printables.com/model/114869-biqu-h2-extruder-part-cooling-duct-mount and...

It should be obvious from the pictures where the fan duct and fan bracket go. The fan sits as low as I felt I could get away with, in order to avoid overly constraining airflow into the intake (which is on top, between the fan and the H2). You will...

This only works if You have a standalone H2 and your nozzle is not flush with the heatblock. Use Creality silent fans. They are already 24v I took the original thing from DaStivi in order to make it compatible with 40mm Fans. The goal is to make a...

Remixed BIQU H2 5015 Cooling Duct by DTDakin (https://www.thingiverse.com/thing:5224768/files) STEPPER MOTOR CONNECTOR IS FACING UP, THEY COME LIKE THIS STOCK NOW BUT IF USING BIQU BX FLIP THE MOTOR AND ROUTE WIRE AROUND BRACKET OVER THE TOP NEXT TO...

This is a remix of a wonderful front linear rail mount for BIQU H2 direct drive extruder. Link to original: https://www.prusaprinters.org/prints/54137-ender-3-linear-rail-hemera-mount You can tinker with it here:...

This is my first fan duct design so it might be rough but it seems to work well so far on my H2. I added photos of the airpath in water to show what its doing.&nbsp;</p><p>Print both parts with supports. The fan duct part works well rotated around...

This is an end stop adjustment for the Biqu H2 direct drive extruder once mounted on the Biqu B1. </p> <p>This brings the nozzle ~3mm onto the bed surface. I will adjust it to bring it to as close to 0 as possible, but this got me up and running...

... down that side of the original part. Stabilty of the Biqu H2 mounted using only one arm with two screws seems adequate. Mounting of this plate to the X carriage uses only two screws which also seems sufficient. It is ugly but functional. ...

Odroid-H2+ to mini-ITX adapter including 2.5" SSD adapter. Probably works with non-plus as well. Created this due to clearance issues with existing designs and plus version. YMMV, please triple check all clearances etc. Be especially careful with...

Odroid H2 2 3.5"HDD NAS Designed in Fusion 360, All panels printed with ABS, side panels should be something stiffer like aluminum. HDD mounts are printed with TPU For structural rigidity, side panels should be made with alu panels. ... Parts...

This only works if You have a standalone H2 and your nozzle is not flush with the heatblock. Use Creality silent fans. They are already 24v I took the original thing from DaStivi in order to make it compatible with 40mm Fans. The goal is to make...

The BIQU H2 is all about being as light and compact as possible. This fan mount has the same design criteria.</p><p>Prints best with a 0.4mm nozzle and in PETG, the extruder motor gets quite hot during use and it might melt ordinary PLA. Layer height...

... Enjoy! Biqu H2 extruder/hotend combo: https://www.aliexpress.com/item/1005002018360184.html 5015 24V blower fan: https://www.amazon.com/gp/product/B0886BQRX4 BLTouch: https://www.amazon.com/ANTCLABS-BLTouch-Leveling-Premium-Extension/dp/B076PQG1FF

Remixed BIQU H2 5015 Cooling Duct by DTDakin (https://www.thingiverse.com/thing:5224768/files) STEPPER MOTOR CONNECTOR IS FACING UP, THEY COME LIKE THIS STOCK NOW BUT IF USING BIQU BX FLIP THE MOTOR AND ROUTE WIRE AROUND BRACKET OVER THE TOP NEXT TO...

A basic mount for the Biqu h2 for the ender 6 this was thrown together as quick as possible so I could get it working. so not the best designed and not the prettiest but it works fine it is held on by the 4 large nuts, this recesses those nuts by...

A mounting bracket to put a Biqu H2 V2S Lite on a Voron X-Carriage-Frame.Only compatible with the old (CW1) X-Frame, since the screws go in from the rear.The extruder is 2mm offset from the x-carriage, so that it clears the right xy-joint.But since...

Update 11.10.21: i was at the point where the stock h2 fan was the loudest part on the printer and i wanted to change it. Im now running a 3510 winsinn 24v fan and it is quieter. ...thats why i had to make the new v3mm because the mounting holes on the...

I've been hard at work for a long time and have had the printer running many hours on this new version, and now the carriage is complete and final, ready for proper use! This is a carriage for the BIQU H2 extruder, made for a single MGN12 linear rail...

I could not find a filament sensor mount for the H2 extruder that mounts one of the generic filament sensors I bought on Amazon. I made one up in SolidWoks. The back side screw holes for the sensor are smaller so that M3 screws will cut threads,...

https://www.thingiverse.com/thing:5385039 If you don't have a bltouch, I would recommend this remix https://www.thingiverse.com/thing:5384889** A Biqu H2 mount for the Artillery Genius and Sidewinder. It has been working great for a few months now. I...

... Heating Rod and Thermistor back into place and carefully tighten the grub screws, being sure not to overtighten and strip them. --Remount H2 --Run cabling --Update RPI --Learn control commands via Python 3 --Figure out the rest... ...lol Enjoy!

j'ai créé ma propre platine pour mon Biqu H2 car les systèmes proposé ne me plaisait pas. j'utilise une ventilo de 40mm pour refroidir l'extrudeur et deux ventilo radial 4010 pour refroidir l'impression ce n'est pas parfait mais ça fonctionne...

Original: https://www.thingiverse.com/thing:4963613 Original remix: https://www.thingiverse.com/thing:5189951 i missed some cut outs for the cable so i remixed it Diffrences: - Cut out for CR/BL Touch cable (in the top braket for the Biqu H2) - Cut...

Sidewinder X1 + Biqu H2 + Bltouch (Gueroloco mod) + Klipper, Voron style : - Led are relocated behind the nozzle (need rewiring) - Nozzle offset change : X -0,88, Y-0,78 - Bltouch offset : X +34, Y -20 - Need : M3 insert x4 M3 Nuts x4 Some M3 screws...

**work in Progress: I need to do an instruction with photography for mounting.** Biqu H2 Mount + cover for Bl-Touch for ender 3, ender3V2, CR10... It is a design that hide cables and have a nice finish. I will make an instruction to ount the...

MKPH2 Wok Range Hybrid Natural Gas/H2 (50/50%), charcoal and induction.├── docs│ └── README.md├── src│ ├── dj_table.py│ ├── closed_cabinet_stove.py│ ├── charcoal_burners│ │ ├── south_america│ │ │ ├── uvacho_colorado.py│ │ │ ├── laranjeira.py│ │ │ └──...

Normally the BIQU H2 is delivered with 24V fan and heater. so if want a matching fan you need to buy a 35mm fan for 12V.</p><p>The original duct fan is to weak for fast printing so i am using a radial fan 5015.</p><p>Two different Ducts. ...If you use a...

... so that you can use M3x5x3 heat inserts 2) Another with 2.5 mm holes to screw the fans directly in PS. The model works well if BIQU H2 extruder is fixed to the caret with the screws from the top and from the back, but not from the bottom.

Remixed BIQU H2 5015 Cooling Duct by DTDakin (https://www.thingiverse.com/thing:5224768/files) STEPPER MOTOR CONNECTOR IS FACING UP, THEY COME LIKE THIS STOCK NOW BUT IF USING BIQU BX FLIP THE MOTOR AND ROUTE WIRE AROUND BRACKET OVER THE TOP NEXT TO...