seckit skgo 3d models

Ball bearing assembly for Z lead screws SK GO with BL-Touch compatibility (may require Z-Endstops removal from rail bracket)\r\n\r\n- Two prints\r\n- Two 608ZZ bearings\r\n- Four M4x10 screws\r\n- Four M4 T-Nuts\r\n

This is an "Assembly Guide" part for the SK-Go2 kit printer. The normal assembly guide for the printer is set up for 170mm spacing - also known as "Frame B". This part provides the 230mm spacing called out in the instructions for assembling the...

<p>Pretty much self explanatory, mounts to add cable chain on your Sk-go core XY printer.</p> <p>Use the M4s and nut that came with the printer to fix the back to it. ...The cable chain itself and the extruder mount uses M3s.</p> <p>Find the cable chain...

mount for LEDs to sk-go or any 2020 extrusion multi angle so when the bed lowers the leds are still illuminating the bed

### SK-Mini Kit Designed for Rigidity, Speed, Low Noise, and Upgradeability. The SK-Mini kit is specifically designed to deliver exceptional rigidity, speed, low noise, and upgradeability. It shares the same structural framework as its counterpart,...

Pretty straight forward thing, you need one M3 nut and bolt to mount it. Probe position is #define NOZZLE_TO_PROBE_OFFSET { 20, 10, -0.9 } To setup your probe, move the nozzle until it touches the bed, put a ziptie between the probe and the bed...

I have created this remix from the original authors STLs because I wanted to print my own cable chain and not buy a plastic part from Amazon. We are makers! This is the cable chain I made these mounts compatible with. ... Category: 3D Printer...

Yes, the drag chain is wayyyy to big (15x40) but it won't flex as much in time.

Yes, the drag chain is wayyyy to big (15x40) but it won't flex as much in time.

People often create simple mounts that fit an M3 hammer nut or drop in t-nut right into the center and then screw onto the bed frame using an M4x12mm bolt. This setup creates a mount where one didn't exist before, eliminating the need for a weird...

Print with PETG or ABS (PLA may overheat near the stepper motor): Print parts: 1x Mount (review the filename for one of three versions) 4x Hex Cab (enhances appearance when installed) Other materials needed: 4x M8x25 screws (millimeters)

Here are the instructions rewritten: Mounting is a straightforward process that requires one M3 nut and bolt. To position your probe, define NOZZLE_TO_PROBE_OFFSET as {20, 10, -0.9}. Setting up your probe involves moving the nozzle until it touches...

This design applies to the second batch of SK-GO, with distinct placement for the power supply unit (PSU) and fuse compared to the initial production run. A cutout is integrated into the design to accommodate the fuse, ensuring comprehensive coverage...

This is a work in progress This is a redesign of the SK-Go cable chain mount by superhans for the SK-Tank. This integrates the stock X endstop mount into one piece. There is also a non cable chain version for cable management. UPDATE -...

For bed movement with lead screws, use one of these: https://www.thingiverse.com/thing:4593598 https://www.thingiverse.com/thing:4826571 First: I've tuned my belted-z SK-Go2 with a new version of bed mounts. On the left side, it's constrained in...

These are mounts for X and Y optical endstops. I used endstops with backward facing connectors. These should be standard. The ones I used for my printer are from [Amazon UK](https://smile.amazon.co.uk/gp/product/B07DK3J88S). As provided the Y...

Stepper mount for dual steppers configuration. You'll need: - 6 nuts (M4) and 6 tnuts (M4) Guide: follow this sequence for easiest path: - install stepper with mount first, you can tighten the screws - install the mount (with stepper) onto...

This is a remix from https://www.thingiverse.com/thing:4286307 Some duct tape makes the installation much easier.

<p>Air filter: Levoit LV-H132</p><p>Fan: 140mm</p><p>The quantities in the CAD are not exact. ...I have 5 “door” holder and 2 sets of magnets to hold the door open.</p><p>I bought 120 of each:</p><p>&nbsp; &nbsp; &nbsp;- 18-8 Stainless Steel Serrated...

<p>Probably gonna change the little finger height.</p><p>!!!!! Important !!!!</p><p>These are 2 5015 fans. ...Be careful when homing your Y axis since it's going to be very close to the frame.</p><p><a...

Print this as densely as possible and mount it to two holes at the top of the printer using a couple of countersunk M5 screws and nuts. This will allow you to mount your Palette to the top of the printer. ... Fusion 360 file included.

While converting my SK-GO2 from sensorless homing to optical endstops, I came across some bumps in the road where certain build aspects can intervene with successful placement of the endstops provided in the fantastic starter kit by caesar_1111. ...

I created this remix of the original STLs because I wanted to print my own cable chain and avoid buying a plastic part from Amazon, opting for a more hands-on approach as a maker. ...This cable chain is what these mounts are designed to be compatible...

<p>KUSBA and Fysetc Accelerometer mounts for Mosquito hot ends , mount directly to the 25mm fan</p>

<p>This model has a modified master plate to allow SK-Tank belts to be attached. &nbsp;The plate has holes at bottom right to connect a mount for the Euclid probe. The holes for the probe mount are sized for two M3 thread inserts (optional)</p><p>The...

This is a custom remix of the SK-Go fan shroud model v2, designed specifically for use with the E3D v6 hotend or clones, modified to seamlessly integrate the Precision Piezo Orion z-probe. The nozzle serves as the probe in this setup. For more...

Here's a fan duct for a 40mm fan to blow air across the row of stepper motor drivers on the Fly CDY V2 3D printer controller. I'm using this set-up on an SK-Tank printer but I've designed the duct to mount to two of the same screws that mount the Fly...

THIS IS THE ONE I USED https://www.altronics.com.au/p/z6516-7-inches-lcd-1024x600-touchscreen-for-raspberry-pi/ https://www.jaycar.com.au/1024x600-hdmi-7in-screen-with-usb-capacitive-touch/p/XC9026...

ABS mount to use a Noctua 40mm with a Volcano hotend on the Seckit Cube.

Designed a cotton swab holder for nozzle cleaning with the Seckit logo.